22
OPERATION / MAINTENANCE
FIREPLACE OPERATION
To operate the gas fireplace, the pilot needs to be running and the gas valve turned to the on position.
You can run the fireplace on manual or remote.
When operating the main burner on manual without
power, the fireplace will operate on low input only. Turn the main power switch to manual to operate the gas features of the fireplace in the event of a power failure.
Turn the main power switches to remote to operate with the gas and the electric features of the fireplace with the remote or thermostat. With power, the manual position
operates the same as the remote position with the exception of the ability to turn off the gas.
Turn the main power switch to the off position to disable both the gas and the electric features of the fireplace.
To configure the remote transmitter to the receiver, see “Privacy Code”.
HAND HELD REMOTE OPERATION
1.Turns accent light on/off.
2.Turns gas flame on/off.
3.Activates gas flame adjustment.
4.Activates fan adjustment.
5.Adjusts options #3 & #4 up.
6.Sets the timer.
7.Adjusts options #3 & #4 down.
8.Sets the time.
FIGURE 50
MANUAL / THERMOSTAT OPERATION
Thermostatic control automatically cycles the fireplace on and off to maintain the desired room temperature. To turn the fireplace burner on, press the gas button. The LCD will display the “Auto” / “OFF” status. Set the desired room temperature using the up or down arrow keys. If the temperature of the room exceeds the set temperature, the thermostat will automatically turn the fireplace off.
Note: If a blower is connected, the thermostatic control will also turn off the blower when the fireplace is turned off.
TO SET THE TIME
Press and hold the CLOCK button until the hour flashes. Adjust the hour using the up or down keys. Press the CLOCK button again to confirm the hour and change to minutes. Again, adjust the minutes using the up or down keys. Finally, press the CLOCK button twice to confirm the settings and return to normal, operating mode.
TIMER OPERATION
The timer setting is used to maintain the desired room temperature for a specific length of time (1 to 120 minutes) that you want the fireplace to operate.
Press the TIMER button once. The LCD will blink "_ _ _". Adjust the time using the up or down arrow keys. (The LCD displays the time chosen.) Press the TIMER button to engage the timer. (When time has expired, the LCD switches to off and displays "_ _ _".)
FLAME HEIGHT
1.With “Auto” displayed, pushing the button marked "flame height" will display a flame image and the current flame setting.
2.Use “UP” “DOWN” buttons to choose 3 different flame levels:1,2,3.
FAN SPEED
1.Pushing the button marked "fan speed" will display a fan image.
2.Use “UP” “DOWN” buttons to choose 3 different fan lev- els:1,2,3.
PRIVACY CODE
1.Remove the cover on the back of the remote transmitter to expose the code switches. Slide the code switches to your
choice of ON or OFF positions. Factory settings are all "OFF".
2.Remove power from the remote CODE SWITCHES receiver by unplugging the power cord or turning power off at the circuit breaker.
3.Take the remote transmitter close to the remote receiver (less than 5 feet from the remote receiver is recommended).
4.Turn on the remote receiver.
5.Install fresh AAA alkaline batteries into the remote trans- mitter. The LCD on the remote transmitter will blink.
6.Press a button on the remote transmitter. The remote re- ceiver will produce a "beep" sound when it receives the code from the remote transmitter.
7.If you do not hear a "beep" sound from the remote receiver, remove batteries from the remote transmitter and power from the remote receiver. Wait for 1 minute and repeat steps 3 to
8.Replace the cover of the remote transmitter and the receiver. The system is now ready to operate.
9.If you desire to operate multiple remote receivers with one remote transmitter, continue to hold the button on the remote transmitter as you bring the remote transmitter within
5feet of each remote receiver then slide the switch on the remote receivers to ON position. Each will acknowledge receipt of coding with a beep.
CHILD-PROOF FUNCTION
When used in this mode, the remote transmitter will work normally but the buttons will be disabled.
Remove the cover at the back of the Remote Transmitter to expose the
