National Instruments NI 8352 Jumper Settings

Appendix B Hardware Configuration

Jumper Settings

Figure B-2 shows the jumper locations on the NI 8352/8353.

Figure B-2. NI 8352/8353 Jumper Locations

1JI

2C1

2JI

2C2

3JPL1

4JPL2

5JPG1

6JBT1

7JP3

8JPF

9JWD

5 6 7

Contents

Main Page Important Information Warranty Copyright Trademarks Patents Compliance Compliance with FCC/Canada Radio Frequency Interference Regulations Determining FCC Class FCC/DOC Warnings Class A Contents About This Manual Chapter 1 Getting Started Chapter 2 Installation and BIOS Setup Chapter 3 I/O Information Page About This Manual Conventions Related Documentation Getting Started Unpacking What You Need to Get Started Key Features Mainboard Features CPU Chipset Memory Page Front Panel LEDs System Management NI 8352/8353 Description Optional Equipment Memory Upgrades Rack Mount Kit USB Floppy Disk Drive NI 8352/8353 Overview National Instruments Software Page Installation and BIOS Setup Safety Information Chassis Cooling Considerations Providing Adequate Clearance Installation Connecting Safety Ground Connecting to Power Source BIOS Setup Main BIOS Setup Menu Main Setup Features Page Page Advanced Setup Boot Features Memory Cache Cache Base 0512K Cache Base 512K640K Cache Extended Memory PCI Configuration Slot1 PCI 32, Slot6 PCI-X 133 MHz, and Slot6 PCI-Exp. x8 Latency Timer Large Disk Access Mode Advanced Chipset Control Clock Spectrum Feature ECC Conditions Advanced Processor Options Thermal Management 2 Adjacent Cache Line Prefetch C1 Enhanced Mode Intel Virtualization T echnology No Execute Mode Memory Protection I/O Device Configuration KBC Clock Input Serial Port A Serial Port B Parallel Port DMI Event Logging Event Log Validity Console Redirection Hardware Monitor Logic Voltage Monitoring IPMI IPMI Specification Version Firmware Version System Event Logging Page System Event Log/System Event Log (List Mode) Realtime Sensor Data Security Supervisor Password Is: User Password Is: Boot Boot Priority Order/Excluded from Boot Orders Exit Exit Saving Changes Exit Discarding Changes Rack Mounting Installing Inner Slides Installing Outer Slides Installing the Slide Assemblies in the Rack Installing the Chassis into the Rack Page Hard Drive Recovery Installing an OS Cleaning Exterior Cleaning I/O Information Rear Panel Connectors PS/2 Universal Serial Bus Serial VGA Page Ethernet MXI-Express Connectors Common Configuration Questions General Questions Boot Options Chassis Configuration Page Upgrade Information Troubleshooting Page A Specifications Electrical AC Input Mainboard CPU Hard Disk Drive Memory Mechanical Environmental Safety Electromagnetic Compatibility CE Compliance Environmental Management Waste Electrical and Electronic Equipment (WEEE) RoHS B Hardware Configuration Figure B-1. NI 8352/8353 Mainboard Layout Jumper Settings Figure B-2 shows the jumper locations on the NI 8352/8353. Figure B-2. NI 8352/8353 Jumper Locations Enable/Disable SMBus to PCI/PCI Express Slots Jumper: JI2C1/JI2C2 Figure B-5. Enable/Disable VGA Connector Jumper: JPG1 Figure B-3. Enable/Disable SMBus to PCI/PCI Express Slots Jumper: JI2C1/JI2C2 Enable/Disable GLAN1/GLAN2 Jumper: JPL1/JPL2 Figure B-4. Enable/Disable GLAN1/GLAN2 Jumper: JPL1/JPL2 Clear CMOS Jumper: JBT1 CompactFlash Master/Slave Select Jumper: JP3 Enable/Disable Power Force On Jumper: JPF Enable/Disable Watchdog Jumper: JWD Other Connectors Figure B-10 shows the locations of other connectors on the NI 8352/8353. Figure B-10. NI 8352/8353 Other Connector Locations Chassis Intrusion Switch Connector: JL1 Front Panel Connector: JF1 Page Front USB Connectors: USB 3/4 and USB 5/6 Power Saving Switch Connector: JGS1 Fan Power Connectors: Fan1 to Fan6 Serial Port Header: COM2 PCI Express Slot Page Page Dual-Channel Memory Configuration Page Page Page Installing DDR Modules Removing DDR Modules Upgrading and Replacing Hard Disk Drives DVD-ROM Connector: IDE1 SATA Connectors: SATA0SATA3 Hard Disk Installation Installing a PCI Express Expansion Card C Intel SATA RAID Utility for Intel ICH7R Intel RAID Configuration Utility Creating a RAID0 Volume Creating a RAID1 Volume Creating a RAID10 (RAID1+ RAID0) Creating a RAID5 Set (Parity) Deleting a RAID Volume Resetting to Non-RAID and Resetting a RAID HDD Exiting the Intel Matrix Storage Manager Utility D Technical Support and Professional Services Glossary Symbols A B C D E F G H I K L M N P R S U V Page Index Numerics A B Page C D E F G H I J K L M N O P Q R S T U V W