NEC PX-42XM5G, PX-50XM6G, PX-60XM5G 50XM6

Rear View/ Terminal Board

50XM6

L

B

D

A

VIDEO

AUDIO 1

DVD1 / HD1

AUDIO 2

RGB2 / DVD2 / HD2

RGB 1

AUDIO 3

RGB 3

EXTERNAL CONTROL

REMOTE

2

R

R

R

1(IN/OUT)

R/Cr/Pr

G/Y B/Cb/Pb HD

VD

DV I ( Digital RGB )

3

Y

Cb/Pb

Cr/Pr

(IN/OUT)

IN

OUT

L (MONO)

L (MONO)

L (MONO)

C

E

F

G

H

I

J

K

AAC IN

Connect the included power cord here.

BEXT SPEAKER L and R

Connect speakers (optional) here. Maintain the correct

polarity. Connect the (positive) speaker wire to the EXT SPEAKER terminal and the (negative)

speaker wire to the EXT SPEAKER terminal on both LEFT and RIGHT channels.

Please refer to your speaker’s owner’s manual.

CVIDEO1, 2, 3 (BNC, RCA, S-Video)

Connect VCR’s, DVD’s or Video Cameras, etc. here. VIDEO1 can be used for Input or Output.

DAUDIO1, AUDIO2, AUDIO3 These are audio input terminals.

The input is selectable. Set which video image corresponds to the audio input from the audio menu screen.

EDVD1 / HD1

Connect DVD’s, High Definition or Laser Discs, etc. here.

FRGB2/ DVD2/ HD2

RGB2:	You can connect an analog RGB signal
	and the syncronization signal.

DVD2/ HD2: You can connect DVDs, High Definition sources, Laser Discs, etc. here.

This input can be set for use with an RGB or component source.

GRGB1 (mini D-Sub 15pin)

Connect an analog RGB signal from a computer, etc. here. This input can be used for Input or Output.

HRGB3 (DVI 24pin)

Connect a digital signal (TMDS) from a source with a DVI output.

This input can be set for use with an RGB3.

IEXTERNAL CONTROL

This terminal is used when operating and controlling the monitor externally with a control system (by RS- 232C).

JREMOTE IN

Connect the remote cable to the remote control’s remote jack to obtain wired remote control.

KREMOTE OUT

Connect the remote cable to the REMOTE IN jack of the other display monitor to obtain wired remote control.

LHandles

Use when installing or carrying the plasma monitor.

Information

•For Y/Cb/Cr, connect to the DVD1 or DVD2 terminals.

•For SCART, this unit provides three ways to connect:

·SCART1: Connect R/G/B to the DVD2 terminals and composite sync. to the HD terminal.

·SCART2: Connect R/G/B to the DVD2 terminals and composite sync. to the VIDEO1 terminal.

·SCART3: Connect R/G/B + composite sync. to the RGB1 terminal.

En-10

Contents

Page Page Precautions CAUTION WARNING Warnings and Safety Precaution WARNING Operating Environment Disposing of your used product Important Information En-2 Contents En-4 Installation Ventilation Requirements for enclosure mounting Creating a video wall Information Cable Management Battery Installation and Replacement Operating Range Using the wired remote control mode Front View qPower wRemote sensor window ePOWER/STANDBY indicator rINPUT SELECT / EXIT Switches the input 42XM5 50XM6 60XM5 Remote Control qPOWER ON/STANDBY Switches the power on/standby wRGB/PC eDVD / HD rVIDEO To turn the unit ON and OFF: To adjust the sound volume: To mute the audio: To check the settings: To adjust the size or quality of the picture automatically: When viewing videos or digital video discs When “PICTURE SIZE” is set to “OFF” Operations in the Side-by-sidemode Operations in the Picture-in-picturemode Selecting the input signals to be displayed Zooming in on a specific input Adjusting the OSM controls Menu Operations Advanced menu mode *The actual screen may be different from the ones in this manual Menu Tree Restoring the factory default settings Adjusting the picture Setting the picture mode according to the brightness of the room Reducing noise in the picture Setting the color temperature Adjusting the color to the desired level Changing the Gamma Curve Making the Low Tone adjustments Adjusting the colors Adjusting the treble, bass and left/right balance and audio input select Setting the allocation of the audio connectors Adjusting the Position, Size, Fine Picture, Picture Adj and Underscan Setting the on-screenmenu Setting the BNC input connector type Setting the RGB1 connector Setting a computer image to the correct RGB select screen Setting high definition images to the suitable screen size Setting the Input Skip Resetting to the default values Setting the power management for computer images POWER/STANDBY indicator Setting the picture to suit the movie Reducing image retention ORBITER settings ORBITER Function settings INVERSE Settings Setting the time To select “ON” for the “WORKING TIME” Setting the gray level for the sides of the screen Setting the screen size for S1/S2 video input Setting the picture size for RGB input signals Setting the signal and black level for DVI signal Setting the Protocol set Using the timer PROGRAM TIMER settings To reset the program To reset the data Special characters in the PROGRAM TIMER screen To set MULTI INPUT Setting the power on mode Enabling/disabling the front panel controls Enabling/disabling remote control wireless transmission Loop Out setting REMOTE ID setting ID number setting Video Wall setting AUTO ID settings IMAGE ADJUST settings P. ON DELAY settings PLE LINK settings Displaying still images in the sub screen Displaying the entire image during DIGITAL ZOOM operations Displaying the information as a text Switching the input source quickly Setting the menu mode Setting the language for the menus Setting the video signal format Checking the frequencies, polarities of input signals, and resolution Type of connector: D-Sub 9-pinmale 1/8 Stereo Mini Jack (not supplied) for REMOTE IN/OUT Symptom Checks Remedy Supported resolution (42XM5) Computer input signals supported by this system Page Supported resolution (50XM6/60XM5) Page 42XM5 50XM6 60XM5