NEC PX-42XM5G, PX-50XM6G, PX-60XM5G ￿AUTO ID settings, ￿PLE LINK settings, ￿P. ON DELAY settings, ￿IMAGE ADJUST settings

Information

￿AUTO ID settings

ON: Enables Auto ID function. In the case shown below, display 1 will be set as ID 1, display 2 as ID2, etc. This can be set only when a 2￿2, 3￿3, 1￿5 or 5￿1 is selected.

			REMOTE
REMOTE	No.1	No.2	OUT	No.1	No.2	REMOTE
IN	No.4	No.3	REMOTE	No.4	No.3	OUT
			IN
	Display 1			Display 2
			REMOTE
			OUT
REMOTE	No.1	No.2		No.1	No.2	REMOTE
OUT	No.4	No.3	REMOTE	No.4	No.3	IN
			IN
	Display 4			Display 3

OFF: Disables Auto ID function.

Note: To use this function, you have to connect the displays with the remote cable (not supplied).

IMAGE ADJUST

The position of the image can be adjusted and flickering of the image can be corrected.

Example: Adjusting the vertical position

On “VIDEO WALL” menu, select “IMAGE ADJUST”, then press the MENU/ENTER button.

The “IMAGE ADJUST” screen appears.

On “V-POSITION” of “IMAGE ADJUST” menu, adjust the position.

	IMAGE ADJUST
ASPECT MODE		:	NORMAL
V-POSITION				: ± 0
H-POSITION				: ± 0
V-HEIGHT				:	0
H-WIDTH				:	0
AUTO PICTURE		:	OFF
FINE PICTURE				:	0
PICTURE ADJ.				:	0
UNDERSCAN		:	OFF			V-POSITION	: +64
SEL.	ADJ.		EXIT RETURN

Information

￿IMAGE ADJUST settings

These are the same functions as the IMAGE ADJUST menu on page En-23.

P. ON DELAY (Power on delay)

Use this function to activate power-on delay.

Turn on the AUTO ID before the following operations.

Example: Setting “ON”

On “P. ON DELAY” of “VIDEO WALL” menu, select “ON”.

VIDEO WALL

DIVIDER		:	1
POSITION
DISP. MODE		:	SPLIT
AUTO ID		:	OFF
IMAGE ADJUST
P. ON DELAY		:	ON
PLE LINK		:	OFF
SEL.	ADJ.		EXIT RETURN

Information

￿P. ON DELAY settings

(Video wall modes other than 4￿4 and 5￿5)

ON: Turns on the main power of each display after a delay time.

*Once this function has been set to “ON”, POWER ON/ OFF button on the remote control does not function except for the No.1 monitor.

By pressing the POWER ON button on the remote En-34

control the No.1 monitor will turn on and the others will be turned on one by one automatically.

*From the second monitor onward, neither the POWER button on the unit nor the POWER ON button on the remote control works. However, by pressing and holding

the POWER ON button for more than 3 seconds, the monitor will be turned on.

OFF: Turns on the main power of all displays at the same time.

(Only for 4￿4 and 5￿5 video wall modes) MODE1: Turns on the main power of each display delayed.

MODE2: Turns on the main power of each display more delayed.

OFF: Turns on the main power of all displays at the same time.

Note: To use this function, you have to connect the displays with the remote cable (not supplied).

PLE LINK

Use this function to set a uniform brightness for each display. Turn on the AUTO ID and set the DIVIDER (at 1, 2￿2, 3￿3, 1￿5 or 5￿1) before the following operations.

Example: Setting “ON”

On “PLE LINK” of “VIDEO WALL” menu, select “ON”, then press the MENU/ENTER button.

VIDEO WALL

DIVIDER		:	1
POSITION
DISP. MODE		:	SPLIT
AUTO ID		:	OFF
IMAGE ADJUST
P. ON DELAY		:	OFF
PLE LINK		:	ON
SEL.	ADJ.		EXIT RETURN

Information

￿PLE LINK settings

ON: Sets a uniform brightness for each screen in a video wall. This can be set only when a 1, 2￿2, 3￿3, 1￿5 or 5￿1 video wall is selected.

OFF: Sets the individual screen brightness for each screen in a video wall.

*When this function is set “ON”, connect your plasma displays with the remote cable (optional) in the order of the position numbers for the 2￿2 video wall. See the drawing below.

*If there are changes in the DIVIDER or POSITION, the PLE LINK will automatically turn OFF.

			REMOTE
REMOTE	No.1	No.2	OUT			No.1	No.2	REMOTE
IN	No.4	No.3		REMOTE		No.4	No.3	OUT
					IN
	Display 1					Display 2
				REMOTE
REMOTE	No.1	No.2		OUT		No.1	No.2	REMOTE
OUT	No.4	No.3	REMOTE			No.4	No.3	IN
			IN
	Display 4					Display 3

*With the 3￿3, 1￿5 or 5￿1 video wall, connect the final display to the first display the same way as with 2￿2 video wall.

Note:

*The remote control can be operated unless the IR REMOTE is set to “OFF”.

*To use this function, you have to connect the displays with the remote cable (not supplied).