Manuals / Brands / Computer Equipment / Computer Hardware / NEC / Computer Equipment / Computer Hardware

NEC uPD780318 Subseries, uPD780328 Subseries, uPD780338 Subseries 3.1 Connection

1 47

Download 47 pages, 478.66 Kb

CHAPTER 3 INSTALLATION

User’s Manual U16214EJ1V0UM

18

3.1 Connection

(1) Connection with IE-78K0-NS or IE-78K0-NS-A main unit

See the IE-78K0-NS User’s Manual (U13731E) for a description of how to connect the IE-780338-NS-EM1 to

the IE-78K0-NS.

See the IE-78K0-NS-A User’s Manual (U14889E) for a description of how to connect the IE-780338-NS-EM1 to

the IE-78K0-NS-A.

(2) Connection with emulation probe

The following shows how to connect the emulation probe to the IE-780338-NS-EM1.

On this board, connect the emulation probe SWEX-120SE-1 to CN5.

Caution Incorrect connection may damage the IE system.

Be sure to read the emulation probe’s user’s manual for a detailed description of the

connection method.

<1> Unfasten one of the screws at the bottom of the connector on the IE system side of the emulation probe

SWEX-120SE-1, and connect and screw on the tip of the FG cable.

Figure 3-1. Connection Between FG Cable and Emulation Probe

Emulation probe

SWEX-120SE-1 (sold separately)

FG cable (supplied with IE-780338-NS-EM1)

Connection connector to

IE-780338-NS-EM1

Contents

Main Users Manual IE-780338-NS-EM1 Page Page Regional Information Device availability Ordering information Product release schedule Availability of related technical literature INTRODUCTION Page Page LIST OF FIGURES Page CHAPTER 1 GENERAL CHAPTER 1 GENERAL 1.1 System Configuration Page CHAPTER 1 GENERAL 1.2 Hardware Configuration Figure 1-3. Basic Hardware Configuration (Using IE-78K0-NS-A) 1.3 Basic Specifications Page CHAPTER 2 PART NAMES 2.1 Parts of Main Unit Figure 2-1. IE-780338-NS-EM1 Part Names Page 3.1 Connection Page 3.2 Clock Settings Page Page Page Page Page Page Page Page CHAPTER 3 INSTALLATION Remark The sections enclosed in broken lines indicate parts that are attached to the parts board. Circuit diagram Page Page Page CHAPTER 3 INSTALLATION 3.3 Mask Option Setting F Connection Pins Part Used Parts Board at Shipment 1-16 Capacitor C1 0.47 F 3-14 Resistor R2 2 M 4-13 Resistor R1 1 M 6-11 Capacitor C2 0.47 F 7-10 Capacitor C3 0.47 3.4 External Trigger 3.5 Jumper Settings on IE-78K0-NS 3.6 Jumper Settings on IE-78K0-NS-A 3.7 Low-Voltage Emulation Settings CHAPTER 4 DIFFERENCES BETWEEN TARGET DEVICES AND TARGET INTERFACE CIRCUITS CHAPTER 4 DIFFERENCES BETWEEN TARGET DEVICES AND TARGET INTERF ACE CIRCUITS Figure 4-1. Equivalent Circuit of Emulation Circuit 1 Figure 4-2. Equivalent Circuit of Emulation Circuit 2 CHAPTER 4 DIFFERENCES BETWEEN TARGET DEVICES AND TARGET INTERF ACE CIRCUITS Figure 4-3. Equivalent Circuit of Emulation Circuit 3 CHAPTER 5 RESTRICTIONS AND CAUTIONS ON USE APPENDIX A EMULATION PROBE PIN ASSIGNMENT TABLE Table A-1. SWEX-120SE-1 Pin Assignments (1/2) Table A-1. SWEX-120SE-1 Pin Assignments (2/2) APPENDIX B CAUTIONS ON DESIGNING TARGET SYSTEM APPENDIX B CAUTIONS ON DESIGNING TARGET SYSTEM Figure B-2. Connection Conditions of Target System Page Page Facsimile Message Thank you for your kind support. From: