Manuals / Brands / Computer Equipment / Computer Hardware / NEC / Computer Equipment / Computer Hardware

NEC uPD780318 Subseries, uPD780328 Subseries, uPD780338 Subseries 3.5 Jumper Settings on IE-78K0-NS, 3.6 Jumper Settings on IE-78K0-NS-A

1 47

Download 47 pages, 478.66 Kb

CHAPTER 3 INSTALLATION

User’s Manual U16214EJ1V0UM 35

3.5 Jumper Settings on IE-78K0-NS

When using the IE-780338-NS-EM1 in combination with the IE-78K0-NS, set the jumper on the IE-78K0-NS as

shown below.

For details of these jumper positions, refer to the IE-78K0-NS User’s Manual (U13731E).

Caution If the jumpers are set incorrectly, the board may be damaged.

Table 3-3. Jumper Settings on IE-78K0-NS

JP2 JP3 JP4 JP6 JP7 JP8

Setting 2 to 3 shorted 1 to 2 shorted 1 to 2 shorted 3 to 4 shorted 1 to 2 shorted Note

Note The settings for the JP8 are as follows.

1-2 shorted: Internal selection of subsystem clock

3-4 shorted: External selection of subsystem clock

3.6 Jumper Settings on IE-78K0-NS-A

When using the IE-780338-NS-EM1 in combination with the IE-78K0-NS-A, set the jumper on the IE-78K0-NS-A

as shown below.

For details of these jumper positions, refer to the IE-78K0-NS-A User’s Manual (U14889E).

Caution If the jumpers are set incorrectly, the board may be damaged.

Table 3-4. Jumper Settings on IE-78K0-NS-A G-780009 Board

JP2 JP3 JP4 JP6 JP7 JP8

Setting 2 to 3 shorted 1 to 2 shorted 1 to 2 shorted 3 to 4 shorted 1 to 2 shorted No te

Note The settings for the JP8 are as follows.

1-2 shorted: Internal selection of subsystem clock

3-4 shorted: External selection of subsystem clock

Table 3-5. Jumper Settings on IE-78K0-NS-A G-78K0H Option Board

JP2

Setting 2 to 3 shorted

Contents

Main Users Manual IE-780338-NS-EM1 Page Page Regional Information Device availability Ordering information Product release schedule Availability of related technical literature INTRODUCTION Page Page LIST OF FIGURES Page CHAPTER 1 GENERAL CHAPTER 1 GENERAL 1.1 System Configuration Page CHAPTER 1 GENERAL 1.2 Hardware Configuration Figure 1-3. Basic Hardware Configuration (Using IE-78K0-NS-A) 1.3 Basic Specifications Page CHAPTER 2 PART NAMES 2.1 Parts of Main Unit Figure 2-1. IE-780338-NS-EM1 Part Names Page 3.1 Connection Page 3.2 Clock Settings Page Page Page Page Page Page Page Page CHAPTER 3 INSTALLATION Remark The sections enclosed in broken lines indicate parts that are attached to the parts board. Circuit diagram Page Page Page CHAPTER 3 INSTALLATION 3.3 Mask Option Setting F Connection Pins Part Used Parts Board at Shipment 1-16 Capacitor C1 0.47 F 3-14 Resistor R2 2 M 4-13 Resistor R1 1 M 6-11 Capacitor C2 0.47 F 7-10 Capacitor C3 0.47 3.4 External Trigger 3.5 Jumper Settings on IE-78K0-NS 3.6 Jumper Settings on IE-78K0-NS-A 3.7 Low-Voltage Emulation Settings CHAPTER 4 DIFFERENCES BETWEEN TARGET DEVICES AND TARGET INTERFACE CIRCUITS CHAPTER 4 DIFFERENCES BETWEEN TARGET DEVICES AND TARGET INTERF ACE CIRCUITS Figure 4-1. Equivalent Circuit of Emulation Circuit 1 Figure 4-2. Equivalent Circuit of Emulation Circuit 2 CHAPTER 4 DIFFERENCES BETWEEN TARGET DEVICES AND TARGET INTERF ACE CIRCUITS Figure 4-3. Equivalent Circuit of Emulation Circuit 3 CHAPTER 5 RESTRICTIONS AND CAUTIONS ON USE APPENDIX A EMULATION PROBE PIN ASSIGNMENT TABLE Table A-1. SWEX-120SE-1 Pin Assignments (1/2) Table A-1. SWEX-120SE-1 Pin Assignments (2/2) APPENDIX B CAUTIONS ON DESIGNING TARGET SYSTEM APPENDIX B CAUTIONS ON DESIGNING TARGET SYSTEM Figure B-2. Connection Conditions of Target System Page Page Facsimile Message Thank you for your kind support. From: