dynamische Mikrophone oder Bändchenmikrophone sowie die Modulationskabel röhrenbestückter Konden- satormikrophone geschaltet werden, ohne dass die Speisegleichspannung abgeschaltet werden muss.

Der Ausgang eines Neumann-Phantomspeisegerätes darf auch auf bereits anderweitig phantomgespeiste Mi- krophoneingänge gesteckt werden.

3.2 Betrieb mit Netzgeräten

Für die Stromversorgung des BCM 104 sind prinzipi- ell alle P48-Netzgeräte entsprechend IEC 1938 geeig- net, die mindestens 3,2 mA je Kanal abgeben.

Das Neumann P48-Netzgerät hat die Bezeichnung N 48 i-2. Es ist zur Stromversorgung zweier Mono- Kondensatormikrophone oder eines Stereomikrophons mit 48 V ± 1 V, maximal 2 x 5 mA, geeignet (siehe auch Neumann-Druckschrift 68832: „48 V-Phantom- speisegeräte“).

Die Zuordnung der Mikrophonanschlüsse und die Po- larität der Modulationsadern ist am Ausgang der Spei- segeräte die gleiche wie am Mikrophon.

N48 i-2 (230 V) ........... sw ............................. Best.-Nr. 06500 N 48 i-2 (117 V) ........... sw ............................. Best.-Nr. 06502

3.3Betrieb an unsymmetrischen oder mittengeerdeten Eingängen

Das 48 V-Phantomspeisegerät N 48 i-2 hat gleichspan- nungsfreie Ausgänge, so dass für den Anschluss an einen unsymmetrischen Eingang kein Übertrager er- forderlich ist.

Beim BCM 104 ist Pin 2 die heiße Phase, und Pin 3 muss für unsymmetrische Eingänge an Masse gelegt werden (siehe Abb. 3).

Bei vielen anderen als den o.g. Phantomspeisegerä- ten liegen nicht nur die Modulationsleitungen zum Mikrophon auf dem Potential der Speisespannung von +48 V, sondern auch die vom Speisegerät abgehen- den Modulationsleitungen. Für die in der Studiotech- nik allgemein üblichen symmetrischen und erdfreien Verstärker- und Mischpulteingänge ist dies ohne Be- deutung.

Dagegen wird die Speisespannung beim Anschluss an unsymmetrische oder mittengeerdete Verstärkerein- gänge kurzgeschlossen, und es ist kein Betrieb mög- lich.

Dann bestehen folgende Lösungsmöglichkeiten:

a)In mittengeerdeten Geräten mit Eingangsübertra- ger (z.B. einige NAGRA-Geräte) kann die betreffen- de Erdverbindung fast immer ohne Nachteile für die Funktion des Gerätes aufgetrennt werden.

condenser microphones, without switching off the DC supply voltage.

No harm is done even if a Neumann phantom power supply is connected to the inputs of microphones which are phantom powered from another source.

3.2 Operation with AC Power Supply

All P48 power supplies in accordance with IEC 1938 which provide at least 3.2 mA per channel are suitable in principle for powering the BCM 104.

The Neumann P48 power supply unit bears the designation N 48 i-2. It is designed to power two mono condenser microphones or one stereo microphone at 48 V ± 1 V, max. 2 x 5 mA (see also Neumann bulletin no. 68832: ”Phantom 48 VDC Power Supplies“).

The assignment of the microphone terminals and the modulation polarity at the power supply output are identical to those at the microphone.

N 48 i-2 (230 V) ...........

blk ..............................

Cat. No. 06500

N 48 i-2 (117 V) ...........

blk ..............................

Cat. No. 06502

3.3Operation with Unbalanced or Center Tap Grounded Inputs

The 48 V phantom powering unit N 48 i-2 has DC- free outputs, so that no transformer is required for connecting to an unbalanced input.

Pin 2 of the BCM 104 is the ”hot“ phase, and pin 3 must be connected to earth for unbalanced inputs (see Fig. 3).

In the case of many phantom powering units other than those mentioned above, not only the modulation leads to the microphone but also the outgoing modulation leads from the powering unit are at the potential of the feed voltage (+48 V). This is unimportant for the balanced, floating amplifier and mixing console inputs which are in general studio use.

However the feed voltage will be short-circuited if connected to unbalanced or center tap grounded amplifier inputs, making operation impossible.

This can be circumvented as follows:

a)In center tap grounded equipment with input transformer (e.g. some NAGRA units), the earth lead can almost always be disconnected without affecting the function of the equipment.

b) In jede abgehende Modulationsleitung kann zur

b) In every outgoing modulation lead, an RC net-

Abblockung der 48 V-Gleichspannung eine RC-Kom-

work can be incorporated to block the 48 Vdc voltage

bination eingefügt werden (siehe Abb. 4 und Neu-

(See Fig. 4 and Neumann-Information no. 84 222).

mann-Information Nr. 84 221).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Abbildung / Figure 3

Abbildung / Figure 4

6

 

 

 

7