New Buck Corporation 261 A, E, F

NOTE: All clearances are to combustibles with all low clearance shields and double wall

pipe , and minimum floor protector.NOTE: Floor protector must extend length of

horizontal flue pipe to wall. NOTE: Model 261 comes standard with low clearance shields.

A B D E F G H I

MODEL 261 14" 4" 16" 8" 3” 47" 10" 84"

LISTED 2100° UL 103 HT TYPE CHIMNEY

REEFER TO MANUFACTURERS

INSTALLATION INSTRUCTION

LISTED 2100° UL 103 HT TYPE

CHIMNEY T-BOX ASSEMBLY

REEFER TO MANUFACTURERS

INSTALLATION INSTRUCTION

SIDE

WALL

Figure 32.

CEILING

Figure 31

BACK WALL

SIDE WALL

A

E

B

F

SIDE WALL

BACK WALL

BUCK STOVE

ALCOVE INSTALLATION

AND CLEARANCES

B-1. Alcove Rear exit using (6" DVL Close Clearance pipe, and any listed 2100° UL 103 HT TYPE Chimney). With standard close clearance shield and pipe shield. Model 261 minimum clearance to combustibles.

PROTECTOR

Contents

Main MODEL 261 NON-CATALYTIC UNIT Page TABLE OF CONTENTS INSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONS MODELS 261 READ THIS FIRST IMPORTANT INSTRUCTIONS WARNING CAUTION CAUTION SECTION I INTRODUCTION POSSIBLE TOOLS NEEDED FOR INSTALLATION INSTALLATION PREPARATION Page SECTION II RESIDENTIAL FREESTANDING VERTICAL EXIT INST ALLATION Floor Protection: Page PREPARING THE ROOM HEATER LOCATION NOTE: CHIMNEY CAUTION: Certain installation types require the use of certain chimney types. HOW TO LOCATE CHIMNEY EXIT, AND INSTALL A. Vertical exit using G D E A Page B G D E A F Page C. Vertical wall exit using (6" Single Wall Pipe minimum 24 ga. blued or black pipe and elbow pipe, and any listed 2100 UL 103 HT. TYPE Chimney and Listed 2100 UL HT T-Box assembly NOTE: Page D. Vertical wall exit using (6" DVL Close Clearance pipe with elbow) , With standard close clearance shield and pipe shield. NOTE: Page NOTE: Page F. Vertical exit using (6" DVL Close Clearance pipe with Elbow) into masonry flue. With standard close clearance shield and pipe shield. SECTION III RESIDENTIAL FREESTANDING REAR EXIT INSTALLATION table of contents Section III MINIMUM CLEARANCES TO FLOOR AND COMBUSTIBLES Floor Protection: Page PREPARING THE ROOM HEATER LOCA TION CHIMNEY HOW TO LOCATE CHIMNEY EXIT, AND INSTALL ( NOTE: ) MINIMUM CLEARANCES FROM TOP OF UNIT TO MANTEL OR MANTEL SUPPORTS Page B. Rear exit into Masonry Flue using (6" DVL Close Clearance pipe). With standard close clearance shield and pipe shield. Page C. Rear exit Vertical then to Horizontal into Masonry Flue DVL Close Clearance DVL CLOSE CLEARANCE PIPE pipe, minimum 24 ga. blued or black pipe) . With standard close clearance shield and pipe shield NOTE: For minimum clearances (See Figure 23). INSTALLATION PREPARATION ( NOTE: ) 8" SECTION IV Alcove Installation Vertical or Horizontal Exit refer back to table of contents Section IV MINIMUM CLEARANCES TO FLOOR AND COMBUSTIBLES Page A-1. Vertical Exit Installation HOW TO LOCA TE CHIMNEY EXIT, AND INSTALL Page A-2. Vertical Exit Installation HOW TO LOCA TE CHIMNEY EXIT, AND INSTALL A NOTE: B E F B-1. Rear Exit Installation HOW TO LOCA TE CHIMNEY EXIT, AND INSTALL A B E F FINAL CHECK CAUTION SECTION V FREESTANDING MOBILE HOME INSTALLA TION Floor Protection: Page FREESTANDING MOBILE HOME INSTALLATION PREPARING THE ROOM HEATER LOCATION CAUTION Page Page Page FINAL CHECK CAUTION SECTION VI WOOD HEATER SAFETY CAUTION SECTION VII OPERATION BUILDING A FIRE SECTION VIII TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Page PRODUCTS COVERED PRODUCTS NOT COVERED WARRANTY TIME PERIODS PROCEDURE CONDITIONS AND EXCLUSIONS OTHER RIGHTS