Manuals / Brands / Household Appliance / Stove / New Buck Corporation / Household Appliance / Stove

New Buck Corporation 261 POSSIBLE TOOLS NEEDED FOR INSTALLATION , INSTALLATION PREPARATION ,

1 53

Download 53 pages, 1.71 Mb

POSSIBLE TOOLS NEEDED FOR INSTALLATION

If you decide to install your own stove, there are several hand tools you may need to do the job.

If you do not already have them, they are readily available at most hardware stores.

Caulking gun

Large adjustable wrench (may not be needed)

Drop cloths or newspapers

Vacuum cleaner or whisk broom

Flashlight

1 tube of RTV silicone, Code 103 or 106, or high temperature rubber cement rated between

450o F- 600o F

7/32” drill bit and electric drill

Socket/Ratchet Set

Wrench

Electric Sawzall

INSTALLATION PREPARATION

1. Locate furniture and other materials away from the area stove will be to allow free access .

2. Cover the adjacent floor areas with the drop cloths to protect from soiling or marring the

surface.

3. If using an existing flue clean it of ashes and soot.

4. Check the flue for excessive build up of creosote or soot. Also, check for obstructions, such

as bird’s nests. If the flue is excessively dirty, clean it, or have someone clean it

professionally BEFORE installing or using the room heater.

5. If the flue is not used , seal off with metal or tightly packed non-combustible insulation .

4

Contents

Main MODEL 261 NON-CATALYTIC UNIT Page TABLE OF CONTENTS INSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONS MODELS 261 READ THIS FIRST IMPORTANT INSTRUCTIONS WARNING CAUTION CAUTION SECTION I INTRODUCTION POSSIBLE TOOLS NEEDED FOR INSTALLATION INSTALLATION PREPARATION Page SECTION II RESIDENTIAL FREESTANDING VERTICAL EXIT INST ALLATION Floor Protection: Page PREPARING THE ROOM HEATER LOCATION NOTE: CHIMNEY CAUTION: Certain installation types require the use of certain chimney types. HOW TO LOCATE CHIMNEY EXIT, AND INSTALL A. Vertical exit using G D E A Page B G D E A F Page C. Vertical wall exit using (6" Single Wall Pipe minimum 24 ga. blued or black pipe and elbow pipe, and any listed 2100 UL 103 HT. TYPE Chimney and Listed 2100 UL HT T-Box assembly NOTE: Page D. Vertical wall exit using (6" DVL Close Clearance pipe with elbow) , With standard close clearance shield and pipe shield. NOTE: Page NOTE: Page F. Vertical exit using (6" DVL Close Clearance pipe with Elbow) into masonry flue. With standard close clearance shield and pipe shield. SECTION III RESIDENTIAL FREESTANDING REAR EXIT INSTALLATION table of contents Section III MINIMUM CLEARANCES TO FLOOR AND COMBUSTIBLES Floor Protection: Page PREPARING THE ROOM HEATER LOCA TION CHIMNEY HOW TO LOCATE CHIMNEY EXIT, AND INSTALL ( NOTE: ) MINIMUM CLEARANCES FROM TOP OF UNIT TO MANTEL OR MANTEL SUPPORTS Page B. Rear exit into Masonry Flue using (6" DVL Close Clearance pipe). With standard close clearance shield and pipe shield. Page C. Rear exit Vertical then to Horizontal into Masonry Flue DVL Close Clearance DVL CLOSE CLEARANCE PIPE pipe, minimum 24 ga. blued or black pipe) . With standard close clearance shield and pipe shield NOTE: For minimum clearances (See Figure 23). INSTALLATION PREPARATION ( NOTE: ) 8" SECTION IV Alcove Installation Vertical or Horizontal Exit refer back to table of contents Section IV MINIMUM CLEARANCES TO FLOOR AND COMBUSTIBLES Page A-1. Vertical Exit Installation HOW TO LOCA TE CHIMNEY EXIT, AND INSTALL Page A-2. Vertical Exit Installation HOW TO LOCA TE CHIMNEY EXIT, AND INSTALL A NOTE: B E F B-1. Rear Exit Installation HOW TO LOCA TE CHIMNEY EXIT, AND INSTALL A B E F FINAL CHECK CAUTION SECTION V FREESTANDING MOBILE HOME INSTALLA TION Floor Protection: Page FREESTANDING MOBILE HOME INSTALLATION PREPARING THE ROOM HEATER LOCATION CAUTION Page Page Page FINAL CHECK CAUTION SECTION VI WOOD HEATER SAFETY CAUTION SECTION VII OPERATION BUILDING A FIRE SECTION VIII TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Page PRODUCTS COVERED PRODUCTS NOT COVERED WARRANTY TIME PERIODS PROCEDURE CONDITIONS AND EXCLUSIONS OTHER RIGHTS