Indicator

 

 

 

 

 

 

Monitor

Viewfinder

 

Solution

0

 

 

—

●

Camera can not focus using autofocus. Change

31,

 

 

(blinks)

composition or focus manually.

55, 60

 

 

 

 

 

 

 

 

 

 

 

 

 

• Use a lower ISO sensitivity

74

 

 

 

 

• Use commercial ND filter

—

 

 

Subject is too bright.

q

•

In mode:

 

 

 

 

 

 

S Increase shutter speed

82

 

 

 

 

 

A Choose a smaller aperture (larger f-number)

83

 

 

 

 

 

 

 

 

 

 

• Use a higher ISO sensitivity

74

 

 

 

 

•

Use flash

70

 

 

Subject is too dark.

r

•

In mode:

 

 

 

 

 

 

S Lower shutter speed

82

 

 

 

 

 

A Choose a larger aperture (smaller f-number)

83

 

 

 

 

 

 

 

 

 

 

A

 

 

 

 

 

No Bulb in S mode.

(blinks)

Change shutter speed or select manual exposure

82, 84

 

 

&

mode.

 

 

 

 

 

 

 

(blinks)

 

 

 

 

 

 

 

 

 

 

 

 

 

Menus and playback not available during interval

 

 

 

Interval timer shooting

—

timer shooting. To end interval timer shooting,

—

 

 

 

 

turn camera off.

 

 

 

 

 

 

 

 

 

 

 

Flash has fired at full power. Check photo in

 

 

 

—

 

monitor; if underexposed, adjust settings and try

—

 

 

 

N

again.

 

 

 

Flash is in TTL mode. Choose

(blinks)

Change flash mode setting on optional flash unit

194

 

 

another setting or use a CPU

 

or use CPU lens.

 

 

lens.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

•

Use the flash.

70

 

 

 

 

• Change distance to subject, aperture, flash

73,

 

 

 

 

 

range, or ISO sensitivity.

74, 83

 

 

—

 

• Optional SB-400 flash unit attached: flash is in

—

 

 

 

 

bounce position or focus distance is very short.

 

 

 

 

N/s

 

 

 

 

 

 

Continue shooting; if necessary, increase focus

 

 

 

 

(blinks)

 

distance to prevent shadows from appearing in

 

 

 

 

 

 

 

 

 

 

 

 

photograph.

 

 

 

 

 

 

 

 

 

 

 

Error occurred updating firmware for optional

 

 

 

Flash error

 

flash unit. Contact Nikon-authorized service

—

 

 

 

 

representative.

 

 

 

 

 

 

 

 

 

 

Eye-Fi upload could not be

 

The Eye-Fi card is still emitting wireless signal after

 

 

 

disabled.

 

 

 

 

 

Disable has been selected for Eye-Fi upload. To

 

 

 

The card is still transmitting

—

173

 

 

terminate wireless transmission, turn the camera

 

 

and pictures may be

 

 

 

 

 

off and remove the card.

 

 

 

uploaded.

 

 

n

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

222