Manuals / Niles Audio / Home Audio / Stereo Amplifier

Niles Audio SI-1230 Step, Description, want to control, current capability of 150 mA, FG00724

Models: SI-1230

1 32

Download 32 pages 47.55 Kb

Page 24

want to control.

Installation

Setting the Turn-On

Mode Switch

The SI-1230 has three turn-on modes. Select the mode you want by sliding the mode switch. See Installation Considerations on page 14 for more information about each of the turn-on modes.

TIP: To conserve energy set the TURN ON mode to either AUDIO SENSE or TRIGGER INPUT. Use of the CONSTANT mode will prevent the amplifier from turning off when not in use wasting energy.

TURN ON MODE

AUDIO SENSE 3-30V

CONSTANTAC/DC TRIGGER INPUT

Slide the switch with either

your fingernail or 1/8”

slotted screwdriver blade

The Control Output

This terminal provides a 12V DC signal suitable for triggering Niles automated switchers, some motorized screens, some electric curtain controls, etc. This voltage is present only when the amplifier is active or on. When the amplifier turns off, the 12V signal is off.

STEP		DESCRIPTION

1.	Check the requirements of the device you	The control output has a maximum
	want to control.	current capability of 150 mA.

2.	Connect the 3.5 mm Jack to the control	Niles makes an accessory cable plug
	output maintaining proper polarity	Niles makes an accessory cable plug
	output maintaining proper polarity	FG00724.
	(tip = +).	FG00724.
	(tip = +).

24		WWW.NILESAUDIO.COM

Image 24

Niles Audio SI-1230 Step, Description, want to control, current capability of 150 mA, output maintaining proper polarity

Contents

I N S T A l l a t i o n G u i d e A M P L I F I E R SSERIES TABLE OF CONTENTS CONGRATULATIONSImportant Safety Instructions 2 Channel, Bridgable Power AmplifiersFCC Required Text Bridgable Power Amplifiers SI-1230Introduction Features and Benefits Freedom from Noise and Cross-TalkTransparent Sound Features and Benefits continued SYSTEM DESIGN BASICS SYSTEM DESIGN BASICS Continued Family RoomLiving Room Listening ZoneCable and Wire SYSTEM DESIGN CONSIDERATIONSSpeaker Compatibility SYSTEM DESIGN CONSIDERATIONS continued These are some of the most common DOs and DON’Ts2 Channel, Bridgable Power Amplifiers Advantages of using the SI-1230in aapplications Single Zone SystemUsing a Dual-ZoneReceiver for Two Listening Zones applicationsZone Home Theater Zoneapplications Expanding a MultiZone System toInclude More Rooms Cableapplications Adding Preamps To Create More Listening ZonesBlu-ray CableCONFIGURING YOUR SYSTEM 2 Channel, Bridgable Power AmplifiersINSTALLATION CONSIDERATIONS INSTALLATION Considerations Placement“Turn-On”Mode Switch FRONT AND REAR PANEL DETAILS3.5 mm Jack for 12v DC Control Output 2 Channel, Bridgable Power Amplifiers FRONT AND REAR PANEL DETAILSGold-platedRCA jacks Serial NumberSTEP DESCRIPTIONInstallation ac power plugInstallation 2 Channel, Bridgable Power AmplifiersSpeaker Wire Connections STEPInstallation BusMatrix Input Switch SettingSTEP “OFF” Position “ON” PositionInstallation 2 Channel, Bridgable Power Amplifiers2. Connect the speaker wires to the two STEPInstallation STEPDESCRIPTION want to controlPower LED Using Level Controls as LimitersOPERATION Bicolor Status LEDListening at Higher Volumes Cleaning and MaintenanceOPERATION Symptom trouble-shootingguide2 Channel, Bridgable Power Amplifiers Possible Causes and Test ProcedurePossible Causes and Test Procedure Symptomtrouble-shootingguide Customer service hoursDetail configuration worksheet For ease of use, the ConfigurationMODE SETTINGS Worksheet can be enlarged on a photocopierLimited Warranty 2 Channel, Bridgable Power AmplifiersREMEDIES FOR BREACH OF WARRANTY ATTENTION TO OUR VALUED CONSUMERS1 - 7 6 0 - 7