Niles Audio specifications SW-800 Woofer Specifications, Features and Benefits

T E C H N I C A L D A T A S H E E T

SW800

S U B W O O F E R

®

SW SUBWOOFER — Designed for low frequency enhancement.

SW-800 WOOFER SPECIFICATIONS

FREQUENCY

RESPONSE

35 Hz to 150Hz +/- 3 dB

RECOMMENDED AMPLIFIER POWER

10 to 150 watts

SENSITIVITY

88 dB 2.83V @ 1 meter.

IMPEDANCE

6 Ohm nominal

HEIGHT X WIDTH

(With frame)

SW-800 Subwoofer	SW-800 In-wall	INTRODUCTION
	Enclosure
		The SW-800/SA-100/SW-800 Enclosure,
		together comprise an in-wall powered
		subwoofer system. This system is ideal
		anywhere additional bass response is
		desired, but bulky traditional floor stand-
		ing subwoofer enclosures just won't
		work. Because of it’s modular design the
		system can be configured for the exact
		requirements of your application.
		SA-100 Subwoofer Amplifier
		FRONT
		REAR
FEATURES AND BENEFITS

14-1/4"H x 10- 3/16" W

HOLE CUTOUT

13-1/8" H x 9-1/8" W

DEPTH BEHIND WALL

(Assumes 1/2” drywall ) Without In-Wall Enclosure

SW-800 3-1/8"

CONNECTIONS

Accommodates up to 12 gauge wire

B L E N D I N G H I G H F I D E L I T Y

A N D A R C H I T E C T U R E ®

Component System

Design

A system can consist of up to four SW-800 in-wall subwoofers, each with SW-800 in wall enclo- sures, and one SA-100 sub- woofer amplifier. Vary the num- ber of SW-800’s to the size of the room. For example, in a large Home Theater you would place three or four SW-800’s and one amplifier. In a small room like a den you would place one SW- 800, controlled by one SA-100 amplifier.

Mica-Filled Polypropylene Woofer

The mica-filled polypropylene cone achieves new standards in transient speed and dynamic range because of its phenomenal rigidity and high stiffness to mass ratio. The inverted butyl sur- round, the BumpBackTM magnet and the rigid steel basket are all optimized for large excursions of

the cone. In this way, an SW-800 delivers exceptionally deep and detailed bass at realistic sound pressure levels, without the mechanically induced limiting and distortion of typical designs.

X-Matrix™Reinforced

Baffle

The X-Matrix baffle design uses specially molded ribs to add rigid- ity to the baffle. Rigidity reduces resonance and coloration, result- ing in more detail and more real- ism at high volume levels.

Absolutely Flush to the Wall Appearance

The unique mounting system of the SW loudspeakers powerfully clamps the frame to the bracket, sandwiching the wall material between them. Because the clamping action is totally uniform around the frame, there are no shadows or gaps between the wall and the frame.

Weather-Proof

Construction

The subwoofer, the frame and the baffle are all weather-proof. The MicroPerf™ aluminum grille is rust proof and the mounting screws are all stainless steel.

Three Stage Installation

System Prevents Theft and

Simplifies Painting

You install only the parts you need for a particular stage of construction. When the framing and wiring are finished, you install the SW-800 in-wall enclosure and bracket. After the drywall is up, but before the painter begins to paint, you install the frame and provide the rustproof aluminum grilles to the painter so that they can be painted to match the surround- ings. Only when construction is completely finished do you put the valuable SW-800 subwoofer in the wall.

CONTINUED OTHER SIDE