ENGLISH / A-13

OPERATING THE MACHINE

The Exterra™ / SR 1900 is a rider-type automatic floor sweeping machine. The controls were designed with one touch operation in mind. For single pass sweeping the operator can simply lower the main broom and all sweeping functions will be ready to go.

Note: Bold numbers in parentheses indicate an item illustrated on pages 8-11.

BEFORE STARTING THE MACHINE

1Be sure you understand all machine controls and their functions.

2Plan your cleaning route. Arrange long, straight passes with as few turns as possible.

3Check the Brake Pedal (FF). The pedal should be firm.

If the pedal is “spongy” or fades under pressure, DO NOT DRIVE THE MACHINE. Report all defects immediately to service personnel.

STARTING THE DIESEL ENGINE

1Turn the Key Switch (TT) counter-clockwise to the “Pre-Heat” position and hold it there until the Glow Plug Indicator (FF) turns OFF. Once the indicator turns OFF the engine can be started. Skip this step if the engine has been running and is already warm.

2Turn the Key Ignition Switch (TT) clockwise to the START position and release it as soon as the engine starts. If the engine does not start after cranking for 15 seconds, release the key, wait for 1 minute and try steps 1-3 again.

3Let the engine run at “IDLE” speed for 5 minutes before using the machine.

4Push the Engine Speed Switch (GG) to switch to “FULL THROTTLE” and move the machine around for 2 or 3 minutes at a slow speed to warm up the hydraulic system.

STARTING THE PROPANE / GASOLINE ENGINE

1NOTE: Propane models only: Open the service valve on the LP fuel tank (21).

2NOTE: 3 Cylinder models: Pull the Choke Knob all the way out. (Skip this step if the engine has been running and is already warm.)

3Turn the Ignition Key Switch (TT) clockwise to the START position and release it as soon as the engine starts. If the engine does not start after cranking for 15 seconds, release the key, wait for 1 minute, then try again.

4NOTE: 3 Cylinder models: Once started, push the Choke Knob in slowly until the engine runs smoothly.

5Let the engine run at “IDLE” speed for 5 minutes before using the machine. NOTE: 3 Cylinder models: Push the Choke Knob all the way in.

6Push the Engine Speed Switch (GG) to switch to “FULL THROTTLE” and move the machine around for 2 or 3 minutes at a slow speed to warm up the hydraulic system.

NOTE: ALWAYS operate the machine with the Throttle Control at full throttle. Use the Forward/Reverse Pedal (G) - not the Throttle Control - to control the speed of the machine. The speed of the machine will increase as the pedal is pushed closer to the floor. Do not press the Forward/Reverse Pedal until the engine has started, this will disengage the starter.

FORM NO. 56041656 - Exterra™ / SR 1900 - A-13

Page 12 Page 14
Page 13
Image 13
Nilfisk-ALTO SR 1900 manual English / A-13, Operating the Machine, Before Starting the Machine, Starting the Diesel Engine
Page 12 Page 14

SR 1900 specifications

The Nilfisk-ALTO SR 1900 is a powerful and versatile scrubber dryer designed to meet the cleaning needs of various commercial environments. Known for its efficiency, durability, and advanced features, the SR 1900 is ideal for maintaining cleanliness in areas such as shopping malls, warehouses, and large retail spaces.

One of the key features of the SR 1900 is its robust cleaning performance. Equipped with a high-capacity dual brush system, the machine efficiently removes dirt and grime from all types of flooring surfaces. The adjustable brush pressure allows operators to customize the cleaning intensity based on the type of surface being cleaned, ensuring optimal results without damaging the floor.

The machine's ergonomic design is another standout characteristic. The user-friendly controls and intuitive layout allow for easy operation, even for those who are new to using scrubber dryers. The compact design ensures excellent maneuverability around tight corners and obstacles, enhancing productivity during cleaning tasks.

A notable technological advancement in the SR 1900 is its innovative water management system. This system regulates water usage, ensuring that the right amount of water is applied to the floor throughout the cleaning process. This not only conserves water but also reduces drying times, allowing foot traffic to resume quicker. Additionally, the SR 1900 features an adjustable squeegee that effectively collects dirty water, minimizing the risk of slips and falls.

The machine operates quietly, making it suitable for use in noise-sensitive environments. The low sound level means that cleaning can take place during business hours without disturbing customers or employees.

The SR 1900 is also designed with ease of maintenance in mind. Its removable tanks and accessible components simplify servicing, reducing downtime and ensuring that the machine remains in optimal working condition.

Overall, the Nilfisk-ALTO SR 1900 is an excellent choice for those looking for a reliable and efficient scrubber dryer. With its robust cleaning capabilities, ergonomic design, innovative technologies, and easy maintenance features, it stands out as a top-tier solution for cleaning professionals striving for high standards of cleanliness in demanding environments.
Top Page Image Contents