4.Pull the Upright Wire Harness (98) up through one of the Handrail Spacers (65). Place the Handrail Spacer (65) on the right Upright (69) as shown, with the cutout turned to- ward the treadmill (see inset drawing A). Place the other Handrail Spacer on the left Upright (not shown).
Have a second person hold the Handrails (66) near the Uprights (69) as shown. Connect the Upright Wire Harness (98) to the wires extending from the Console Base (81). Insert the connectors and the Wire Harness into the hole in the Console Base (see inset drawing B).
Set the Handrails (66) on the Spacers (65), being careful not to pinch the Wire Harness (98).
5.Insert two Handrail Bushings (75) into the right Upright (69). Turn the Handrail Bushings so they fit against the Upright, with the thick sides of the Bushings facing the center of the treadmill, as shown in the inset drawing.
Insert two Handrail Bolts (78) with Handrail Washers
(77)into the Handrail Bushings (75), the right Upright (69), and the right Handrail Spacer (65). Lift the right Handrail (66) slightly to align the Bolts with the holes in the Handrail. Next, thread the Bolts into the Handrail
(66).Do not tighten the Bolts yet.
Attach the left Handrail (not shown) in the same way. Tighten all four Handrail Bolts (78).
4 | Cutout | A |
|
| |
| 81 |
|
|
| |
|
| 66 |
|
| 69 |
|
|
|
|
| |
|
|
|
|
| 65 |
| 98 | 69 | B | 98 |
|
| 65 |
|
|
|
|
|
|
|
|
| 81 |
5 |
|
|
|
|
|
|
|
| 66 |
|
|
|
| 65 |
|
| |
|
|
| 69 |
|
|
|
|
| 75 |
|
|
|
|
|
| 77 | Thick |
|
|
|
| Side | |
|
|
|
|
| |
| 75 | 77 |
| 78 |
|
|
|
|
| ||
6.Make sure that all parts are tightened before you use the treadmill. Note: If there is a thin sheet of clear plastic on the hood decal or the “ComforTrack” decal, remove it. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 24). To protect the floor or carpet from damage, place a mat under the treadmill.
If you purchase the optional chest pulse sensor (see page 21), follow the steps below to install the receiver included with the chest pulse sensor.
1.Make sure that the power cord is unplugged. Remove the indicated Screws from the Console Back (88).
Important: The Screws may be different lengths. Keep track of which Screws were removed from which holes.
2.See drawing 2a. Peel the paper off the pad on the bottom of the Receiver (A). Turn the Receiver so the cylinder is on the side shown, and press the Receiver into the bot- tom of the Console Base (81) in the indicated location. See drawing 2b. Connect the Short Jumper Wire (B) to the wire on the Receiver (A). Connect the other end of the Jumper Wire to the PULSE jack on the back of the Console (82). Note: The included Long Jumper Wire and Wire Tie are not needed and can be discarded.
Make sure that no wires are pinched. See step 1 above. Reattach the Console (82) with the Screws. Note: If the
Screws are not put in the correct locations, the Console will be damaged.
88 |
Screws |
2a | 81 | 2b | 82 |
|
|
|
| 82 |
|
| PULSE |
|
|
|
| Jack | |
|
|
|
|
| |
|
| A |
|
|
|
Cylinder |
|
|
|
| |
|
|
| B | A |
|
|
|
|
| 7 | |
|
|
|
|
| |
