Part ListÑModel No. NTTL24080 |
| R0599A | |||
To find the parts listed below, refer to the Exploded Drawing attached in the center of this userÕs manual. | |||||
Key No. Qty. | Description | Key No. Qty. | Description | ||
1 | 2 | Cushion Plate | 53 | 1 | Electronics Bracket |
2 | 4 | Cushion Plate Screw | 54 | 1 | Incline Motor |
3 | 2 | Adjustable Deck Cushion | 55 | 1 | Controller |
4 | 2 | Rod Screw | 56 | 8 | Base Pad |
5 | 1 | Cushion Rod | 57 | 4 | Wheel Spacer |
6 | 1 | Cushion Knob Screw | 58 | 4 | Plastic |
7 | 1 | Cushion Knob | 59 | 1 | Power Board w/Clips |
8 | 2 | Foot Rail Cover | 60 | 2 | Caution Decal |
9 | 1 | Left Foot Rail | 61 | 8 | Belly Pan Spacer |
10 | 1 | Left Foot Rail Endcap | 62 | 8 | Belly Pan Screw |
11 | 2 | Endcap Screw | 63 | 1 | Sensor Unit |
12 | 15 | Plastic Fastener | 64 | 1 | Right Rear Endcap |
13 | 2 | Front Isolator | 65 | 2 | Endcap Washer |
14 | 2 | Motor Mount Washer | 66 | 2 | Endcap Screw |
15 | 32 | 3/4Ó Screw | 67 | 2 | Frame Endcap |
16 | 2 | Cushion Board | 68 | 2 | Rear Roller Adj. Bolt |
17 | 2 | Platform Screw | 69 | 1 | Warning Decal |
18 | 2 | Motor Star Washer | 70 | 1 | Belly Pan |
19 | 2 | Rear Isolator | 71 | 1 | Left Rear Endcap |
20 | 1 | Catch | 72 | 1 | Rear Roller |
21 | 4 | Catch Screw | 73 | 2 | Frame Pivot Bolt |
22 | 1 | Walking Platform | 74 | 2 | Frame Pivot Washer |
23 | 1 | Walking Belt | 75 | 1 | Left Frame Pivot Cap |
24 | 1 | Front Roller/Pulley | 76 | 24 | Small Screw |
25 | 1 | Magnet | 77 | 1 | Motor Hood |
26 | 4 | Motor Mount Nut | 78 | 2 | |
27 | 1 | Motor | 79 | 1 | Belly Pan |
28* | 1 | Motor Assembly | 80 | 1 | Power Cord |
29 | 1 | Front Roller Pulley | 81 | 1 | Power Cord Grommet |
30 | 1 | Motor Adjustment Bolt | 82 | 1 | Circuit Breaker |
31 | 1 | Motor Plate | 83 | 1 | On/Off Switch |
32 | 1 | Motor Pivot Nut | 84 | 2 | Upright Endcap |
33 | 1 | Motor Mount Plate | 85 | 1 | Releasable Tie |
34 | 4 | Motor Isolator | 86 | 1 | Tie Clamp Screw |
35 | 4 | Motor Bolt | 87 | 1 | Tie Clamp |
36 | 2 | Motor Mount Bolt | 88 | 8 | 8Ó Cable Tie |
37 | 5 | Frame Pivot Nut | 89 |
| 4Ó Cable Tie |
38 | 2 | Frame Spacer | 90 | 1 | 8Ó Green Ground Wire |
39 | 1 | Reed Switch Clip | 91 | 2 | Shock |
40 | 1 | Frame | 92 | 1 | Upright/Base |
41 | 5 | Screw | 93 | 2 | Lift Frame Bolt |
42 | 2 | Side Hood Mount | 94 | 2 | Receiver Screw |
43 | 2 | Front Hood Mount | 95 | 1 | Receiver |
44 | 1 | Transformer | 96* | 1 | Hand Pulse Sensor |
45 | 1 | Bottom Incline Motor Bolt | 97 | 1 | Motor Pivot Bolt |
46 | 4 | Incline Motor Nut/Lift Frame Nut | 98 | 2 | Latch Bolt |
47 | 1 | Lift Frame | 99 | 1 | Top Incline Motor Bolt |
48 | 2 | Motor Tension Nut | 100 | 1 | Lock Pin |
49 | 5 | Roller Adj. Washer/Latch Washer | 101 | 1 | Lock Pin Clip |
50 | 3 | Front Roller Nut/Cushion Nut | 102 | 1 | Lock Pin Collar |
51 | 1 | Incline Sensor Wire | 103 | 1 | Lock Pin Spring |
52 | 1 | Motor Belt | 104 | 1 | Latch Bracket |
30
