Operation Instructions

1. Engaging the PTO

While seated on the tractor and the engine at idle, engage the PTO. Slowly increase the throttle until the needle in the generator voltmeter is at or above the black line in the green area.

2. Applying a Load

It is important to determine the total electrical load before it is connected to the generator. Always compare the generator nameplate data with that of the equipment to be used to ensure that watts, volts, amperage, and frequency requirements are suitable for operating equipment. The wattage listed on the equipment nameplate is its rated output. However, some equipment may require three to ten times more wattage than its rating on the nameplate, as the wattage is influenced by the equipment efficiency, power factor and starting system. NOTE: If wattage is not given on equipment nameplate, approximate wattage may be determined by multiplying nameplate voltage by nameplate amperage.

VOLTS

X AMPS

= WATTS

Example: 120V

X 5A

= 600W

Also, a chart of estimated load requirements for some appliances and tools is shown on page 11.

When connecting a resistive load such as incandescent lights, heaters or common electric power tools, a capacity of up to the generator full rated wattage output can be used.

When connecting a resistive-inductive load such as a fluorescent or mercury light, transformers or inductive coils, a capacity of up to 0.6 times the generator’s full rated output can be used.

Always allow the generator to reach operating speed before a load is applied.

Important: The two major factors in determining the life of a generator head are heat build up caused by overloading the generator and corrosive contaminants that attack the wiring insulation. If the generator is overloaded, the wires become excessively hot and cause the insulation to break down, reducing its ability to resist corrosive contaminants. Over time the effectiveness of the insulation is eliminated and a dead short can result.

Apply the load to the generator. Remember to stay clear of the rotating PTO driveline. From the tractor seat re-adjust the speed until the needle on the generator voltmeter is close to the black line in the green area. If the needle will not rise to the green area no matter what the engine speed, the generator is either overloaded or there is a problem. Use the troubleshooting guide at the end of the manual for assistance with possible problems.

3. Operating Speed

The generator must be run at the correct speed in order to produce the proper electrical voltage and frequency.

The output voltage should be checked to ensure the generator is working properly subsequent to connecting a load to the generator. Failure to do so could result in damage to equipment plugged into the unit and possible injury to the individual.

All engines have a tendency to slow down when a load is applied. When the electrical load is connected to the generator, the engine is more heavily loaded, and as a result the speed drops slightly. This slight decrease in speed, together with the voltage drop within the generator itself, results in a slightly lower voltage when the generator is loaded to its full capacity than when it is running with no load. The slight variation has no appreciable effect in the operation of motors, lights and most appliances. Electronic equipment and clocks will be affected if correct RPM is not maintained. See Load vs. Output chart.

Output voltage should be checked periodically to

 

Load

 

Output

 

 

 

 

ensure continued proper operation of the generator

 

 

 

 

Percent of

Speed

Frequency

Generator

 

and appliances. It can be checked with a portable

 

 

 

Generator

(RPM)

(Hz)

Voltage at 120V

 

meter. Frequency can be checked by using an electric

 

 

 

Output

 

 

Receptacle

 

clock with a sweep second hand. Timed against a

 

 

 

 

 

0%

3780

63.0

125V

 

wristwatch or a stopwatch the clock should be correct

 

 

 

50%

3600

60.0

122V

 

within +/- 2 seconds per minute. All speed setting

 

100%

 

 

 

 

3480

58.0

118V

 

adjustments should be done by a qualified technician.

 

 

 

 

 

 

 

 

 

 

 

 

9

Page 8 Page 10
Page 9
Image 9
North Star M165951C owner manual Operation Instructions, Engaging the PTO, Applying a Load, Operating Speed
Page 8 Page 10

M165951C specifications

The North Star M165951C is a cutting-edge vessel designed for maritime operations, merging advanced technology with exceptional durability and performance. This versatile watercraft is engineered for various applications including research, transportation, and exploration, making it a popular choice among professionals in the marine industry.

One of the standout features of the M165951C is its robust construction. The hull is crafted from high-strength materials that provide excellent resistance against harsh marine environments. This durability ensures the vessel can withstand rough seas and inclement weather, guaranteeing safe operations in challenging conditions.

The North Star M165951C is equipped with state-of-the-art navigation and communication technologies, enhancing its operational efficiency. The integration of advanced GPS systems allows for precise positioning, enabling seamless travel across distances. Coupled with sophisticated radar and sonar equipment, the vessel can effectively navigate and survey underwater landscapes, making it an ideal choice for research and exploration missions.

Powering the M165951C is a highly efficient propulsion system that delivers remarkable speed and maneuverability. The vessel utilizes a combination of fuel-efficient engines that reduce operational costs while maintaining high performance standards. This engine configuration not only increases the vessel's range but also minimizes its environmental footprint, aligning with modern sustainability goals.

The interior of the North Star M165951C is designed for comfort and functionality. With spacious cabins and advanced amenities, it provides a conducive environment for crew members and passengers alike. The ergonomic layout ensures ease of access and operational efficiency during marine missions. The vessel is also equipped with essential safety features, including life rafts, fire suppression systems, and emergency beacons, ensuring maximum safety for all onboard.

In summary, the North Star M165951C stands out in the maritime industry due to its robust construction, advanced technologies, and practical design. Boasting exceptional performance capabilities and a strong commitment to safety and sustainability, it is a vessel that meets the evolving demands of modern maritime operations. Whether used for scientific research or commercial purposes, the North Star M165951C continues to set a high standard in the world of marine vessels.
Top Page Image Contents