INSTALLATION IN NEW CONSTRUCTION

WALL INLET ROUGH-IN

1.Once the locations for wall inlets have been determined, mount all inlet brackets.

2.To locate bracket on wall stud, measure approximately 18" up from finished floor level. (Height may vary according to individual preference.)

3.Refer to Figure 4. Model 361 for using 360 inlet. Nail bracket to side of stud so that front edge of bracket is flush to front of stud. (The bracket may also be nailed to the front edge of the stud. For front stud mounting, use locating tabs on bracket for proper alignment.)

4.Refer to Figure 5. Model 329 for use with 330 inlets. Remove cardboard from plaster guard frame. Using four (4) provided screws, attach the appropriate flanged fitting and inlet seal to back of inlet.

5.Replace cardboard in plaster guard frame.

6.When using Model 329 glue elbow to mounting plate.

NOTE: Configuration of spacer may vary depending upon installation.

NOTE: When using the Model 361 inlet bracket on walls thinner than 12", use a 14" spacer (not furnished) between the wall and the inlet bracket. See Figure 5A.

Spacer may be made from plywood, masonite, etc. Contact cement may be used to hold spacer in place during assembly.

FIGURE 5

 

 

MODEL 361

MODEL 329

SIDE

FACE

 

 

MOUNTING

MOUNTING

FIGURE 4

2 3/8"

1 13/16"

 

 

INLET MOUNTING

SPACER

WALL LESS THAN

 

1/4"

1/2" THICK.

BRACKET

 

 

31/4" PLASTER

21/4" GUARD

HOLE

FIGURE 5A

INSTALLING THE TUBING

INSTALLATION HINTS

Use the following installation guidelines when installing the tubing.

1.Start tubing installation at farthest inlet and work toward the power unit.

2.Tubing run to the power unit should be as straight as possible.

3.When assembling sections with elbows and tees, make sure the curve in the fitting is aligned so that the air flows toward the power unit.

4.Branch lines should always join the trunk line from above or from the same level. Never join a branch line from an angle below the trunk line.

5.Secure tubing to joists or studs.

6.Refer to Figure 20 on page 7. Run low voltage wiring and secure wiring to tubing. Leave approximately 6" of wire for connection to each inlet.

 

MODEL 361 MOUNTING

 

 

21/2" DIA. HOLE

 

 

THROUGH SOLE PLATE

 

2 3/8"

 

113/16"

 

113/16"

113/16"

SIDE

 

FACE

MOUNTING

 

MOUNTING

 

MODEL 329 MOUNTING

 

 

2"

21/2" DIA. HOLE

 

THROUGH SOLE PLATE

 

 

2"-382s

 

 

25/8-382

FIGURE 6

FACE

 

MOUNTING

 

4

Page 4
Image 4
NuTone CV352 manual Installation in NEW Construction, Wall Inlet ROUGH-IN, Installing the Tubing, Installation Hints

CV352 specifications

The NuTone CV352 is a premier central vacuum system designed for homeowners seeking efficiency, power, and convenience in their cleaning routines. This model is part of NuTone's esteemed CV series, which is known for its superior performance and reliability. With a powerful motor and an array of features, the CV352 is well-equipped to elevate your home cleaning experience.

One of the standout features of the NuTone CV352 is its robust motor, which delivers an impressive 550 air watts of suction power. This ensures that it can easily handle various types of debris, from fine dust to larger particles. The powerful motor not only improves cleaning efficiency but also reduces the need for frequent emptying, making it suitable for larger homes.

Another noteworthy aspect of the CV352 is its unique filtration system. It comes equipped with a high-efficiency particulate air (HEPA) filter, which captures 99.97% of particles as small as 0.3 microns. This feature is particularly beneficial for allergy sufferers, as it effectively minimizes allergens and improves indoor air quality. The filtration system is designed for easy maintenance, allowing homeowners to replace or clean filters with minimal effort.

The NuTone CV352 also integrates advanced sound-dampening technology, which significantly reduces the operational noise of the system. This feature is a game-changer for households that prioritize a peaceful environment, allowing users to enjoy a quieter cleaning experience without disturbing family members or pets.

Ease of use is another hallmark of the CV352. The central vacuum system comes with a variety of accessories, including a crevice tool, dusting brush, and upholstery nozzle, making it versatile for all cleaning tasks. Its wall-mounted design saves valuable floor space and the convenient on/off switch can be easily accessed from the hose handle, providing a seamless user experience.

Durability is a key characteristic of the NuTone CV352. Built with high-quality materials, it is designed to withstand the rigors of daily cleaning. The system is backed by a generous warranty, reflecting the manufacturer's confidence in its long-lasting performance.

In summary, the NuTone CV352 central vacuum system combines powerful suction, advanced filtration, reduced noise levels, and user-friendly features to create a superior cleaning solution for any home. Its thoughtful design and capabilities make it a worthwhile investment for those looking to enhance their home cleaning process.