Manuals / Oki / Computer Equipment / Printer

Oki 425S manual Rewinder Winding Evaluation Continuous Print Test Receipt

Models: 425S

1 133

Download 133 pages 21.41 Kb

Page 43

2.7 Rewinder Winding Evaluation Continuous Print Test (Receipt)

This function performs print/platen switch continuous test to evaluate the rewinder winding performance.

(1)How to start

Turn the power on while holding down SW3 + SW1 + SW4.

(2)How to exit

Turn the power off.

•During test printing, if you press SW1, printing suspends. If you press SW1 again, printing resumes.

(3)Contents printed

(a)Prints “HHH”+ Space + “HHH” (UTL characters)

(b)Print Sheet Mode switching (Receipt ÆSlip ÆReceipt)

Developer’s Guide: English 43

Image 43

Oki 425S manual Rewinder Winding Evaluation Continuous Print Test Receipt

Contents

Okipos 425S Mail Address Mailing AddressWeb Site Contents Specifications Using the Unitool Printer Driver Command DescriptionSelect a Location Where to install your printerGetting Started UnpackingGetting to Know the Okipos 425S Installing the PrinterRemove the Shipping Restraints Setting the DIP Switches RS-232C Setting the Interface Board AssemblyInstalling the Interface Board Assembly Connecting the Power Connecting the ComputerConnecting the Cash Drawer Connecting the Customer DisplayInstalling the Ribbon Cartridge Unpack the ribbon cartridge Developer’s Guide English Paper Specifications Maximum thickness 0.3 mm 0.012 inches Installing the PaperRoll paper Adjusting the Roll Paper GuideOkipos 425S Loading the Roll Paper Mount it following the above procedures 3 Adjusting the Roll Paper Near End Sensing Position Loading the Cut-Sheet Paper Slip Cut-Sheet Paper SlipLoading the Cut-Sheet Paper Validation/Stub Cut-Sheet Paper Validation/StubHow to remove the Piece Developer’s Guide English Loading the Sprocket Paper Tractor Sprocket Paper TractorDeveloper’s Guide English Okipos 425S Developer’s Guide English Operation Panel Operation Panel FunctionsSW2 FF/LOD,PAK SW3 CUT SW1 Switching FunctionsLED PowerLED Function LED OFFTypes Local FunctionsSW2 SW3 SW1 SW4 StartingOEM Standard Model Menu Function ReceiptOverview HSD OKI Standard ModelStart How to OperateOperation Hex Dump Function Receipt How to PrintPrint Format Using the Micr Reader Option How to use the Micr Reader Micr Read Test Receipt When Read is NG When Read is OKReturn code Status Rewinder Winding Evaluation Continuous Print Test Receipt Replacing the Ribbon Cartridge MaintenanceImportant! Do not remove the ribbon shield 1 from the ribbon Okipos 425S Replacing the Roll Paper Okipos 425S Print head may be very hot. Exercise caution Clearing Paper JamsOkipos 425S Print head may be hot. Exercise caution Cut-Sheet PaperSprocket Paper Alarm Indication for a Failure Troubleshooting and RepairDetails of Alarm Indications LED Indication LED LED 1 Error LED 2 StatusBlink Introduction CharacteristicsScope of Application Options Configuration Agency Approvals General SpecificationsPower Requirements Environmental ConditionsDkstatus Communication Interface SpecificationsParallel Interface OKI/OEM Standard Type GNDRTS DSR DTR Init 2 RS-232C Interface OKI Standard TypeCASHDV1 CASHST-N Cash Drawer connector OKI Standard TypeCASHDV2 DTR DSR Printhead Physical CharacteristicsPrinter Maximum Number of Characters per line Logical CharacteristicsPrint Direction Selectable Character PitchesLine Feed Speed Printer PerformanceFont Size/Cell Size Line Feed PitchesCut-Sheet Paper Slip/Validation Media SpecificationsCut-Sheet Paper Counterfoil/Stub Sprocket Paper Tractor Cut-Sheet Paper Slip/Validation Appendix Media SpecificationsPaper Size and Printing Area Okipos 425S Developer’s Guide English Paper Quality Paper Weight and Maximum Duplicating QuantityFixing Method of Multi-part Paper Joint Binding Holes Perforated Lines Provisions on Fold, Bend and Curl on Cut-sheet Paper Paper size and Printing area Roll paperPaper Quality Paper WeightSprocket Paper Tractor Developer’s Guide English Paper Quality D E Okipos 425S Position Deviation of Sprocket Holes Rising in Horizontal Perforated LineBinding Holes Corner Cut Wrinkle, Pleat and Swell Paper Size and Scanning Area Micr only with Micr TypePaper Tear-off Paper Feed SpecificationsPaper feed methods/Paths Paper Positioning RestrictionsMicr Specifications Only with Micr type Reliability Ribbon SpecificationsFunction Code Control Code ListHEX DEC Code DC2 Can ESC ESC ESC @ ESC SequenceHEX 1B OD ESC SI ESC DLE DHEX GS sequenceUS Sequence DLE Sequence HEX DEC Code DC2 Can DLE ESCESC = n Data GS ENQ FS SequenceCode table OEM Standard Type Character Set1.1 USA Canada-French Multilingual Portugal Norway Brascii Abicomp Multilingual ISO 8859/15 International character set table 2.1 USA Code table OKI Standard TypeCanada-French Multilingual Portugal Norway Brascii Abicomp Multilingual ISO 8859/15 International character set table Setting Slip Paper in the Paper Tray Using the Unitool Printer DriverUsing Registered Paper Icons Okipos 425S Developer’s Guide English Using Paper Size that is less than 187.96 mm 7.4 in Width Using Custom SizeImage of actual printing area Example Developer’s Guide English Okipos 425S Developer’s Guide English About the Validation Printing Area Symbol Designation Standard ValueData in application Print result Example Orientation Setting Tractor Paper in the Tractor UnitOkipos 425S Developer’s Guide English