Oki RT322POS - page 11

– 7 –

(1) Make sure the printer is turned off.

(2) Install the ferrite core onto the ethernet cable as shown

in the illustration below.

(3) Pass the fastener through the ferrite core.

(4) Loop the fastener around the cable and lock it. Use scis-

sors to cut off any excess.

(5) Connect the interface cable to the connector on the rear

panel of the printer.

10 cm

(maximum)

Fastener

Ferrite core

Ethernet cable

3-2-4. Connecting Ethernet Cable

If a ferrite core is included, install the ferrite core onto the Ethernet cable according to the fol-

lowing procedure to prevent electrical noise.

If a ferrite core is not included, perform steps (1) and (5) only.

When using an Ethernet cable that is 10 m or less, shielded cable is recommended.

Ethernet interface board

IFBD-HE07

Ethernet interface board

IFBD-HE05

Contents

Main Page TABLE OF CONTENTS Page 1. Unpacking and Installation 1-1. Unpacking 1-2. Choosing a place for the printer 3 2. Parts Identication and Nomenclature 3. Setup 3-1. Connecting the Cable to the PC 3-2. Connecting the Cable to the Printer Page Page 3-3. Installing the Printer Software 3-4. Connecting the Optional AC Adapter Page Page 3-7. Loading the Paper Roll Page Page Caution Symbol Notes on Using the Auto Cutter 4. Consumable Parts and AC Adapter 4-1. Thermal Paper Roll Page 4-2. Thermal Label Paper Roll (Tack Label Paper) 20 Detailed Diagrams of Recommended Tack Label Specications Detailed Diagram of Effective Printing Range 4-3. AC adapter (option) 5. Control Panel and Other Functions 5-1. Control Panel 5-2. Errors Page 5-3. Self-Printing 6. Adjusting the Sensor 6-1. Adjusting the Near End Sensor Position Page 6-2. PE and BM ( Paper End and Black Mark ) Sensor Adjustment 6-3. NE (Near End) Sensor Adjustment 7. Preventing and Clearing Paper Jams 7-1. Preventing Paper Jams 7-2. Removing Paper Jam Caution Symbol 8. Periodical Cleaning 8-1. Cleaning the Thermal Head 8-2. Cleaning the Rubber Roller 8-3. Cleaning the Sensors and the Surrounding Areas 8-4. Cleaning the Paper Holder and the Surrounding Area 9. Specications 9-1. General Specications 9-2. Auto Cutter Specications 9-3. Interface 9-4. AC Adapter (Option) 9-5. Environmental Requirements 9-6. Reliability Specications 9-7. Black mark specications 10. Dip Switch Setting 10-1. Parallel Interface Model DIP-SW 1 The functions of switches 1-3 through 1-10 will change according to the command emulation (2) Star Page Mode Page 10-2. RS-232C Interface Model DIP-SW 1 The functions of switches 1-3 through 1-10 will change according to the command emulation (2) Star Page Mode Page Page 10-3. USB Interface Model 2) Star Page Mode (3) ESC/POS mode DIP-SW 2 10-4. EthernetInterface Model DIP-SW 1 The functions of switches 1-3 through 1-10 will change according to the command emulation 2) Star Page Mode Page Page 11. Parallel Interface Parallel interface connector (printer side) 12. RS-232C Serial Interface 12-1. Interface Specications 12-2. RS-232C Connector Page 51 12-3. Cable Connections The followings are a recommended interface cable connections. Note: Use shielded wire less than 3 m in length. 12-4. Electrical Characteristics Voltage Data signal Control signal Binary status -3 V to -15 V Mark OFF 1 +3 V to +15 V Space ON 0 13. USB and Ethernet Interface 13-1. USB Interface Specications 13-2. Ethernet Interface Specications Modular plug 14. Peripheral Unit Drive Circuit Drive circuit The recommended drive unit is shown below. Page 15. Memory Switch Settings