Olympus 033 7

●Do not use the following chemicals for cleaning, corrosion prevention, prevention of fogging, repair or other purposes. When these are used for the Case directly or indirectly (with the chemicals in vaporized state), they may cause cracking under high pressure or other problems.

Chemicals which cannot be used Explanation

Do not clean the Case with alcohol, gasoline, Volatile organic solvents, thinner or other volatile organic solvents or with

chemical detergents chemical detergents etc. Pure water or lukewarm water is sufficient.

Do not use anticorrosion agents. The metal parts

Anticorrosion agent use stainless steel or brass, and washing with

pure water is sufficient.

Commercial defogging	Do not use commercial defogging agents. Always
agents	use the specified desiccant silica gel.

Grease other than specified Use only the specified silicone grease for the

silicone greasesilicone O-ring, as otherwise the O-ring surface may deteriorate and water leakage may be caused.

Do not use adhesive for repairs or other purposes.

AdhesiveWhen repair is required, please contact a dealer or a service station of OLYMPUS IMAGING CORP.

●Do not perform operations other than specified in this instruction manual, do not remove or modify parts other than specified, and do not use parts other than specified.

Any troubles in taking pictures or with the equipment resulting from the above actions shall be outside the guarantee.

●OLYMPUS IMAGING CORP. shall be in no way responsible for accidents involving immersion of a digital camera in water.

●OLYMPUS IMAGING CORP. shall not pay any compensation for accidents (injury or material damage) at the time of use.

E-6

Contents

For the digital camera Stylus 720 SW, µ 720 SW Introduction Please read the following items before use For safe use Page Batteries Setting the underwater shooting scene mode For Prevention of Water Leakage Accidents Handling the Product Page Contents 1.Preparations 2.Advance Check of the Case 3.Install the digital camera 4.Taking Pictures Under Water 6.Handling After Shooting 7.Maintaining the Waterproof Function 1. Preparations Check the contents of the package Names of the parts Install the strap Installation explanation Master the basic operation Holding the Case How to Press the Shutter How to Switch Between the , and SCN Modes How to Use the Zoom Buttons 2. Advance Check of the Case Advance test before use Advance Test 3. Install the digital camera Check the digital camera Battery Confirmation Remove the hand strap from the digital camera Prepare the camera Applicable Digital Cameras Turn the digital camera ON Check the camera’s operation Open the Case Load the digital camera Insertion of silica gel Make sure the camera is loaded properly Seal the Case Check the operation of the loaded camera Confirm the shooting scene and shooting mode Installation and Removal of the LCD Hood Installation Removal Mounting and Removing the Lens Cap Perform the final checks Visual Inspection Final Test 4. Taking Pictures Under Water How to Use the Hand Strap Take pictures carefully Confirm the picture on the LCD monitor Quietly press the shutter lever Underwater shooting modes Underwater Wide-Angle1 Underwater Wide-Angle2 Underwater Macro TIP How to select the shooting scene AF lock during underwater shooting 6. Handling After Shooting Wipe off any waterdrop Take out the digital camera Wash the Case with pure water Dry the Case 7. Maintaining the Waterproof Function Remove the O-ring Remove any sand, dirt, etc When a mechanical pencil or a similar other sharp object is used to remove the Install the O-ring How to Apply Grease to the O-ring Replace consumable products 8. Appendix Q & A on the use of the PT-033 (c)Places with volatile substances (d)Places with vibrations (d) (a)Hitting other objects (b)Dropping Q6 : How should I take pictures under water A6 : Please observe the following items for shooting under water (1)Fix the protector with the accessory hand strap to your wrist Q7 : can I check for water leakage Q8 : What are the causes for entry of water Q9 : What are the important points for O-ringmaintenance A9 : Please observe the following items Use the original Olympus silicone A thin, uniform coat produces the best result (4)The O-ringis a consumable product. Replace it at least once a year water is sufficient dealer Q11: Please tell me about repairs Q12: What are the model names of the accessories for the PT-033 A12: The following accessories are being sold Specifications