Omega OMB-DAQBOARD-3000 - page 34

System Example

A DaqBoard/3000 Series system example which includes both a PDQ30 and a DBK215 is illustrated on

page 2-4. For convenience, it has been repeated below. In regard to the PDQ30 aspect:

1) Connection from PDQ30 to DaqBoard/3000 is made via a CA-266-3 (or CA-266-6) HDMI cable.

2) PDQ30’s analog input lines connect via removable screw-terminal blocks (TB1 through TB6).

3) A pinout for PDQ30 follows shortly.

4) Users of DBK215 should refer to Appendix A.

5) Instead of connecting a DBK215 to the DaqBoard/3000 series 68-pin SCSI connector, a TB-100

terminal board option can be connected. The TB-100 option is discussed on page 2-3.

DaqBoard/3000 Connected to a PDQ30 and to a DBK215*

*Note: The DBK215 offers screw terminal connections and BNC connections in an enclosure. If BNC connectors and an

enclosure are not needed, a TB-100 Terminal Connector option can be connected to the 68-pin SCSI connector instead

of the DBK215. See page 2-3 for TB- 100 information. Refer to Appendix A for DBK215

information.

2-6 Connections & Pinouts 918494 DaqBoard/3000 Series User’s Manual

Contents

Main Users Guide Servicing North America: U.S.A.: Canada: For immediate technical or application assistance: U.S.A. and Canada: Warnings, Cautions, Notes, and Tips Specifications and Calibration Page Table of Contents Page Page DaqBoard Installation Guide Step 1 Install Software IMPORTANT: Software must be installed before installing hardware. Step 2 Install Boards in available PCI Bus-slots IMPORTANT: Software must be installed before installing hardware. CAUTION IMPORTANT: Bus Mastering DMA must be Enabled. Step 3 Configure Boards Using Add Device Step 4 Test Hardware Page Device Overviews 1 Block Diagrams Connections Product Features I/O Comparison Matrix Signal I/O Analog Input Synchronous I/O Input Scanning Page Page Page Analog Input & Channel Expansion Bus Mastering DMA Triggering Calibration Analog Output Digital Inputs and Outputs Digital Outputs and Pattern Generation Counter Inputs Timer Outputs Multiple DaqBoards per PC Software Page Connections and Pinouts 2 Pinout for DaqBoard/3000 Series Boards TB-100 Terminal Connector Option DaqBoard/3000 Series Users Manual 918494 Connections & Pinouts 2-3 PDQ30 Analog Expansion and DBK215 Connector Options DBK215 PDQ30 CAUTION Page Page Page CE-Compliance 3 Overview CE Standards and Directives Safety Conditions Emissions/Immunity Conditions Calibration 4 Page DaqCal User Calibration Utility Contents CAUTION Overview Equipment P1 P4 100-PIN P5 SCSI 68-PIN NIST Traceability Installing DaqCal Setup P1 P4 P5 SCSI What to Expect when using DaqCal Page Calibrating Analog Outputs Calibrating DBK Expansion Options Counter Input Modes 5 Debounce Page Page Page Terms Applicable to Counter Modes Gating: Mapped Channel: Start of Scan: Terminal Count: Encoder Mode Counter/Totalize Mode Page Period Mode Page Frequency Ranges for a 16-bit value, sampling error is less than 0.21% Frequency Ranges for a 32-bit Value, Sampling Error is Less than 0.21% Pulsewidth Mode Page Timing Mode Page Encoder Mode Page For Single-ended Connections: Wiring for 1 Encoder Page Page Setpoint Configuration for Output Control 6 Using Setpoints to Control Outputs Page Detecting Input Values Controlling Analog, Digital, and Timer Outputs Page P2C, DAC, or Timer Update Latency More Examples of Control Outputs Detection on an Analog Input, DAC and P2C Updates Analog Inputs with Setpoints Update on True and False Detection on an Analog Input, Timer Output Updates Using the Hysterisis Function Using Multiple Inputs to Control One DAC Output The Setpoint Status Register Page Specifications DaqBoard/3000 Series and PDQ30 7 DaqBoard/3000 Series Specifications I/O Comparison Matrix General Specifications Analog Inputs A/D Specifications Input Sequencer Scan Clock Sources: 2 External Acquisition Scan Clock Input Triggering Analog Outputs Digital I/O One Digital I/O Channel, Typical Pattern Generation Output Counters One Counter Channel, Typical Frequency/Pulse Generators Software PDQ30 Specifications General Analog Inputs PDQ30 Type T Thermocouple Typical Performance of 12 PDQ30 Units; 0C (Note 1) Accessories and Cables Appendix A With 68-Pin SCSI Adaptability for Analog I/O, Digital I/O, & Pulse/Frequency Page Connection Tips System Example Using the Screw-Terminal Blocks In general, the following terminal block-to-signal relationships apply: DBK215 Board * ** Analog I/O Correlation to 68-pin SCSI Also see Correlation to BNC Terminations (TB13 and TB14) on page DBK215-10. Digital I/O Correlation to 68-pin SCSI Pulse/Frequency Correlation to 68-pin SCSI Correlation to Analog Input BNC Terminations BNC 0 through BNC 7 Correlation to Custom BNC Terminations BNC A through BNC H Pertains to Terminal Blocks TB15 and TB16 for Custom Configuration on a per-channel basis. Adding Resistor/Capacitor Filter Networks WARNING CAUTION Page Specifications for DBK215 Page Appendix B An Important Note Regarding Hardware Analog Level Trigger and Comparator Change State Page Glossary Page WARRANTY/DISCLAIMER RETURN REQUESTS/INQUIRIES M4254/0106 Where Do I Find Everything I Need for Process Measurement and Control? OMEGAOf Course! Shop online at omega.com TEMPERATURE PRESSURE, STRAIN AND FORCE FLOW/LEVEL pH/CONDUCTIVITY