Advanced
Digital Input Signal Formats
The following table shows the display indicators for each supported digital signal format.
Format | Display | |||||
|
|
|
|
|
|
|
Dolby Digital |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DTS |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PCM |
|
| PCM | |||
|
|
|
|
|
|
|
Normally, the AV receiver detects the signal format auto- matically. However, if you experience either of the fol- lowing issues when playing PCM or DTS material, you can manually set the signal format to PCM or DTS:
•If the beginnings of tracks from a PCM source are cut off, try setting the format to PCM.
•If noise is produced when fast forwarding or reversing a DTS CD, try setting the format to DTS.
|
|
|
|
|
|
| TUNING | / PRESET | MASTER VOLUME |
STANDBY/ON |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ENTER |
| |
| STANDBY |
|
|
|
|
|
|
|
|
A SPEAKERS B | TONE | + | STEREO | LISTENING MODE | DISPLAY DIGITAL INPUT | RT/PTY/TP MEMORY TUNING MODE | RETURN | SETUP |
|
|
|
|
|
|
| CLEAR |
|
PHONES |
|
|
|
|
|
|
|
MULTl CH | DVD | VIDEO 1/VCR | VIDEO 2 | VIDEO 3 | TAPE | TUNER | CD |
DIGITAL INPUT
Correcting Sound and Picture Sync
When using progressive scanning on your DVD player, you may find that the picture and sound are out of sync. With this setting, you can correct this by delaying the audio signals. You can set it to 0, 20, or 40 milliseconds.
ON/STANDBY
REMOTE MODE
RECEIVER DVD | RECEIVER |
TAPE |
|
INPUT SELECTOR
INPUT | 1 | 2 | 3 | CD |
V1 | V2 | V3 |
| |
SELECTOR |
| |||
4 | 5 | 6 | MD | |
|
| |||
|
| MULTI CH | DVD |
|
| 7 | 8 | 9 | CDR |
| TAPE | TUNER | CD |
|
| +10 | 0 | CLR | HDD |
| DIMMER | SLEEP |
| |
|
|
| CH | VOL |
|
|
| DISC | |
|
|
| ALBUM |
|
| TOP MENU |
|
| MENU |
| SP A / B |
|
| MUTING |
|
| ENTER |
| |
| PLAYLIST |
| PLAYLIST | |
| RETURN |
|
| SETUP |
1 | Press the [RECEIVER] REMOTE |
| |
RECEIVER | MODE button. |
1 | Press and hold the AV receiver’s [DIGITAL |
| INPUT] button for about 3 seconds. |
|
|
2 | While “Auto” is displayed (about 3 sec- |
| onds), press the [DIGITAL INPUT] button |
again to select: PCM, DTS, or Auto.
DTS or PCM: The DTS or PCM indicator, depending on which format you have set, flashes, and only signals in that format are output. Digital signals in other formats are ignored.
2
V1 V2 V3
DVD
Press and hold, for more than 4 seconds, the input selector but- ton for the input source that you want to correct.
This can be the [DVD], [VIDEO 1], [VIDEO 2], or [VIDEO 3] input source.
Auto (default): The format is detected automati- cally. If no digital input signal is present, the cor- responding analog input is used instead.
3 Use the Left and Right []/[ ] buttons to set the delay to 0, 20, or 40 milliseconds.
The previous display reappears if you don’t do anything for 5 minutes.
Note:
•This setting is not available when the Direct listening mode is used with an analog input signal.
54