Onkyo specifications En HTP-980, Enjoying Home Theater, Specifications, Front speakers SKF-980

Wall

3/16" to 7/16" (5 to 10 mm)

7.1ch Home Theater Speaker Package

En HTP-980

Front speakers (SKF-980)				Surround speakers (SKR-980)	Center speaker (SKC-980)
				Surround back speakers (SKB-980)
						(Green)
		(White)	(Red)	(Blue)	(Gray)	Speaker cable 10 ft.
		Speaker cables 11 ft.		Surround speakers*2	Center speaker*1
						(3.0 m)
	Front speakers*1	(3.5 m)
				(Brown)	(Tan)
*1	For magnetic shielding.			Speaker cables 26 ft. (8.0 m)
*2	Non-magnetic shielding.
					Cork spacer (12 pcs.) for front and

Surround back speakers*2 center speakers

Keyhole slot	Speaker terminals
	Keyhole slot
Speaker	SKC-980
terminals
	Speaker
SKR-980/SKB-980	terminals
	Keyhole slots
SKF-980

Wall Mounting

Powered subwoofer (SKW-980)

RCA cable 10 ft. (3.0 m)

Subwoofer*2

*2 Non-magnetic shielding.

■Front

Standby/On indicator

Red: Subwoofer in standby mode

Blue: Subwoofer on

With the Auto Standby function, the SKW-980 automatically turns on when an input signal is detected in Standby mode. When there’s no input signal for a while, the SKW-980 automatically enters Standby mode.

■ Rear

OUTPUT LEVEL control

This control is used to adjust the vol- ume of the subwoofer.

	LINE INPUT
	This RCA input should be connected to
To AC outlet	the subwoofer pre out on your AV

To mount the front/surround/surround back speakers vertically, use the keyhole slot shown to hang each speaker on a screw that’s securely screwed into the wall.

Keyhole slots for wall mounting

SKF-980SKR-980/SKB-980

To mount the center speaker horizontally, use the two keyhole slots shown to hang each speaker on two screws that are securely screwed into the wall.

Keyhole slots for wall mounting

SKC-980

10-1/4" (260 mm)

Caution

• A mounting screw’s ability to support a speaker depends on how well it’s anchored to the wall. If you have hollow walls, screw each mounting screw into a stud. If there are no studs, or the walls are solid, use suitable wall anchors. Use screws with a head diameter of 5/16" (9 mm) or less and a shank diameter of 1/8" (4 mm) or less. With hollow walls, use a cable/pipe detector to check for any power cables or water pipes before making any holes.

•Leave a gap of between 3/16" (5 mm) and 7/16" (10 mm) between the wall and the base of the screw head, as shown. (We recommend that you consult a home installation professional.)

receiver with supplied RCA cable.

Caution

•The front grille is not designed to be removed so does not attempt to remove it forcibly, as this will damage it.

Note

• The Auto Standby function turns the subwoofer on when the input signal

exceeds a certain level. If the Auto Standby function does not work reli-

ably, try slightly increasing or decreasing the subwoofer output level on

your receiver.

• If the Standby/On indicator lights (both red and blue LEDs) several sec-

onds or minutes after the sound output stopped, this means that the amp

protection circuit has been activated. In this case, set the OUTPUT LEVEL

control to the center position, and disconnect the power cord from the AC

Using the Cork Spacers for a More Stable Platform

We recommend using the supplied cork spacers to achieve the best possible		■ Attaching and detaching the speaker grilles
sound from your speakers. The cork spacers prevent the speakers from mov-		The front, center, surround and	Removal
ing, providing a more stable platform.				Replacement
		surround back speakers have
Cork spacers		detachable grilles.
		See the right illustrations to attach
Bottom of the
	Bottom of the SKC-980	or detach them.
SKF-980
	Cork spacers

Enjoying Home Theater Specifications

outlet. Wait at least 10 seconds, and then reconnect the power cord. If that

doesn’t solve the issue, contact your Onkyo dealer.

Setting the Subwoofer Level

Make sure the SKW-980 subwoofer’s output level control is set at the “THX-POSITION”. You can then adjust the level as needed.

The Home Theater means that you can enjoy surround sound with a real sense of movement in your own home — just like being in a movie theater or concert hall.

■Powered Subwoofer (SKW-980)

■Center Speaker (SKC-980)

fab c

Corner	1/3 of wall
position
	position

de gh

abFront left and right speakers (SKF-980)

They should be positioned facing the listener at about ear level, and equally spaced from the TV. Angle them inward slightly so as to create a triangle, with the listener at the apex.

cCenter speaker (SKC-980)

Position it close to your TV (preferably on top) facing forward at about ear

level, or at the same height as the front left and right speakers. deSurround left and right speakers (SKR-980)

Position them at the sides of the listener, or slightly behind, about 2 to 3 feet (60 to 100 cm) above ear level. Ideally they should be equally spaced from the listener.

fSubwoofer (SKW-980)

The subwoofer handles the bass sounds of the LFE (Low-Frequency Effects) channel. The volume and quality of the bass output from your subwoofer will depend on its position, the shape of your listening room, and your listening

position. In general, a good bass sound can be obtained by installing the sub- woofer in a front corner, or at one-third the way along the front wall, as shown.

ghSurround back left and right speakers (SKB-980)

These speakers further enhance the realism of surround sound and improve sound localization behind the listener.

Position them behind the listener about 2 to 3 feet (60 to 100 cm) above ear level.

Type	Acoustic suspension
Rated output power	125 watts minimum continuous power,
	6 ohms, driven at 100 Hz with a
	maximum total harmonic distortion of
	1 %
Input sensitivity/impedance	330 mV / 100 kΩ
Frequency response	20 Hz to 100 Hz
Cabinet capacity	49 L (1.73 cubic feet)
Dimensions (W ⋅ H ⋅ D)	380 mm ⋅ 444 mm ⋅ 429 mm
	(14-15/16" ⋅ 17-1/2" ⋅ 16-7/8")
	(incl. grille and projection)
Weight	15.5 kg (34.2 lbs.)
Drivers unit	30 cm (12") Cone Woofer
Power supply	AC 120V, 60 Hz
Power consumption	140 W
Other	Auto Standby function

■Front Speakers (SKF-980)

Type	2	Way Acoustic suspension
Impedance	8	Ω
Maximum input power	130 W
Sensitivity	83 dB/W/m
Frequency response	50 Hz to 45 kHz
Crossover frequency	2 kHz

Type	2 Way Acoustic suspension
Impedance	8 Ω
Maximum input power	130 W
Sensitivity	83 dB/W/m
Frequency response	50 Hz to 45 kHz
Crossover frequency	2 kHz
Cabinet capacity	7.5 L (0.265 cubic feet)
Dimensions (W ⋅ H ⋅ D)	433 mm ⋅ 158 mm ⋅ 199 mm
	(17-1/16" ⋅ 6-1/4" ⋅ 7-13/16")
	(incl. grille and projection)
Weight	5.3 kg (11.7 lbs.)
Drivers unit	12 cm (5") A-OMF Cone Woofer ⋅ 2
	2.5 cm (1") Soft Dome Tweeter ⋅ 1
Terminal	Binding post (Banana type supported)
Other	Magnetic shielding

■Surround and Surround Back Speakers (SKR-980/SKB-980)

Type	2	Way Acoustic suspension
Impedance	8	Ω
Maximum input power	130 W
Sensitivity	81 dB/W/m

Connecting the Speakers

Surround	Surround	Surround	Surround	Front left	Front right
back left	back right	left	right
				speaker	speaker
speaker	speaker	speaker	speaker

Cabinet capacity	7.5 L (0.265 cubic feet)
Dimensions (W ⋅ H ⋅ D)	158 mm × 433 mm × 199 mm
	(6-1/4" ⋅ 17-1/16" ⋅ 7-13/16")
	(incl. grille and projection)
Weight	5.3 kg (11.7 lbs.)
Drivers unit	12 cm (5") A-OMF Cone Woofer ⋅ 2
	2.5 cm (1") Soft Dome Tweeter ⋅ 1
Terminal	Binding post (Banana type supported)
Other	Magnetic shielding

Frequency response	50 Hz to 45 kHz
Crossover frequency	2 kHz
Cabinet capacity	4.6 L (0.163 cubic feet)
Dimensions (W ⋅ H ⋅ D)	200 mm ⋅ 275 mm ⋅ 169 mm
	(7-7/8" ⋅ 10-13/16" ⋅ 6-5/8")
	(incl. grille and projection)
Weight	3.5 kg (7.7 lbs.)
Drivers unit	13 cm (5-1/8") A-OMF Cone Woofer ⋅ 1
	2.5 cm (1") Soft Dome Tweeter ⋅ 1
Terminal	Binding post (Banana type supported)

				Speaker Connection
Brown	Tan	Blue	Gray	Precautions
			White	Read the following before connecting your
				speakers:
			Red	• Turn off your receiver before making any
			Center speaker	connections.
				• Pay close attention to speaker
				wiring polarity. Connect posi-
				tive (+) terminals to only pos-
			Green	itive (+) terminals, and
				negative (–) terminals to only negative (–)
				terminals. If the speakers are wired incor-
Powered				rectly, the sound will be out of phase and
				will sound unnatural.
subwoofer
				• Be careful not to short the positive and
				negative wires. Doing so may damage
				your amp.
				Note
				• When you connect the front high left and right
				speakers, prepare for it separately, or use the
				surround back left and right speakers.

Specifications and appearance are subject to change without prior notice.

THX and the THX logo are trademarks of THX Ltd. which are regis- tered in some jurisdictions. All rights reserved.

Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN

Tel: 072-831-8023 Fax: 072-831-8163

ONKYO U.S.A. CORPORATION

18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.

Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/

ONKYO EUROPE ELECTRONICS GmbH

Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY

Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.eu.onkyo.com/

ONKYO EUROPE ELECTRONICS GmbH (UK BRANCH)

The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK

Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700

ONKYO CHINA LIMITED

Unit 1 & 12, 9/F, Ever Gain Plaza Tower 1, 88, Container Port Road, Kwai Chung,

N.T., Hong Kong. Tel: 852-2429-3118	Fax: 852-2428-9039
http://www.ch.onkyo.com/	Y1005-1

SN 29400481

(C) Copyright 2010 ONKYO CORPORATION Japan. All rights reserved.

* 2 9 4 0 0 4 8 1 *