Before using this unit
Worldwide models are equipped with a voltage selector to conform with local power supplies. Be sure to set this switch to match the voltage of the power supply in your area before plugging in the unit. Determine the proper voltage for your area:
If the preset voltage is not correct for your area, insert a screwdriver into the groove in the switch. Slide the switch all the way to the upper (120 V) or to the lower
DIGITAL |
| PRE OUT |
|
|
|
| AUDIO | VIDEO | S VIDEO | COMPONENT |
|
|
|
|
|
|
| |
OUTPUT | FRONT | R | L | ANTENNA |
|
| VIDEO |
| FRONT SPEAKERS | SURR SPEAKERS |
|
| ||||||
|
|
|
|
|
|
|
|
|
| MONITOR |
| CAUTION: | R | L | R | L |
|
|
OPT |
|
|
|
|
|
|
|
|
| OUT | Y |
|
|
|
|
|
| |
| SUB |
|
| CENTER |
|
| R | L |
|
|
| SPEAKER |
|
|
|
|
|
|
|
|
|
|
| AM |
|
|
|
|
| IMPEDANCE |
|
|
|
| AC OUTLET |
| |
DIGITAL |
|
|
|
|
|
|
| OUT |
| ZONE 2 | P | 64 OHMS MIN. |
|
|
|
| SWITCHED |
|
INPUT |
|
|
|
|
|
|
|
|
|
|
| /SPEAKER |
|
|
|
| 100W MAX. |
|
COAX | SURR |
|
|
|
|
|
|
|
|
|
| SEE |
|
|
|
|
|
|
1 |
|
|
|
|
|
|
| IN |
| DVD | P | INSTRUCTION |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| MANUAL FOR |
|
|
|
|
|
|
| SURR |
|
|
|
|
|
|
|
|
| INPUT 1 | CORRECT |
|
|
|
|
|
|
2 | BACK |
|
|
|
| FM |
| OUT |
|
| Y | SETTINGS. |
|
|
|
|
|
|
|
|
|
|
| 75 |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
| RAUDIO L |
|
|
|
| VIDEO 1 |
| VOLTAGE |
|
|
| ||||
3 | FRONT |
|
| MULTI CH |
|
|
| IN |
|
| P |
|
|
|
|
|
|
|
|
|
| INPUT |
|
|
|
|
|
|
|
|
|
|
|
| |||
OPT | SUB |
|
| CENTER |
|
|
|
|
|
| INPUT 2 | SELECTOR |
|
| SELECTOR | |||
1 | SURR |
|
|
|
| PH |
| OUT |
|
|
|
| ||||||
|
|
|
|
|
|
|
| P |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| VIDEO 2 |
|
|
| EN ER |
| SURR BACK |
| VOLTAGE |
|
|
|
|
|
|
|
|
|
|
|
|
| SPEAKER |
| SPEAKER |
| ||
2 |
|
|
|
|
| CD |
| IN |
|
| Y |
|
| I R | 12V TRIGGER |
| MODEL NO. / | 120V |
| BACK |
|
|
|
| OUT |
|
|
|
|
|
|
| IN | ZONE 2 |
|
| |
| SURR |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3 |
|
|
|
|
|
|
| IN |
| VIDEO 3 | P |
|
|
|
|
|
| |
| R |
|
| L |
| TAPE |
|
|
|
|
| 120V |
| REMOTE |
|
|
| |
DIGITAL | GND |
|
| R | L | IN |
|
|
|
|
| OUT |
|
|
| |||
|
|
| IN |
| VIDEO 4 | P |
| CONTROL |
|
|
| |||||||
INPUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
| AUDIO |
|
| AUDIO | VIDEO | S VIDEO |
|
|
|
|
|
|
|
|
Point the remote controller toward the remote control sensor. The STANDBY indicator lights up when the unit receives a signal from the remote controller.
Remote control sensor
STANDBY indicator
30˚
30˚
Approx. 16 feet (5 meters)
1.Remove the battery compartment cover by pressing and sliding the cover.
2.Insert two AA (R6 or
3.After batteries are installed and seated correctly, replace the compartment cover.
1 | 2 | 3 |
Notes:
•Do not mix new batteries with old batteries or different kinds of batteries.
•To avoid corrosion, remove the batteries if the remote controller is not to be used for a long time.
•Remove dead batteries immediately to avoid damage from corrosion. If the remote controller does not operate smoothly, replace both the batteries at the same time.
Notes:
•Place the unit away from strong light such as direct sunlight or inverted fluorescent light which can prevent proper operation of the remote controller.
•Using another remote controller of the same type in the same room or using the unit near equipment which uses infrared rays may cause operational interference.
•Do not put objects on the remote controller. Its buttons may be pressed by mistake and drain the batteries.
•Make sure the audio rack doors do not have colored glass. Placing the unit behind such doors may prevent proper remote controller operation.
•If there is any obstacle between the remote controller and the remote control sensor, the remote controller will not operate.
7