Onkyo TX-NR414 En-44, Digital Audio Digital Audio Input, Sp Config Speaker Configuration, Front

Digital Audio (Digital Audio Input)

1 2 3 4 “Setup” 5

Menu Digital Audio

Advanced Operations

Sp Config (Speaker Configuration)				■ Center*1, Surround*1
				`Small:
1	2	3	4 “Setup” 5	`Large:
				Select based on the cone diameter.

`None

Menu Sp Config Note

If you connect a component to a digital audio input, you must assign that input to an input selector. For example, if you connect your CD player to the OPTICAL IN 1, you must assign “OPTICAL1” to the “TV/CD” input selector. Here are the default assignments.

Input selector	Default assignment
BD/DVD	COAXIAL1
CBL/SAT	COAXIAL2
GAME	OPTICAL1
PC	- - - - -
AUX	- - - - -
TV/CD	OPTICAL2

■BD/DVD, CBL/SAT, GAME, PC, AUX, TV/CD

`COAXIAL1, COAXIAL2, OPTICAL1, OPTICAL2:

Select the input to which the component has been connected.

`- - - - -:

Select if the component is connected to an analog audio input.

Note

•When an HDMI IN is assigned to an input selector in

“HDMI Input” (➔ page 43), the same HDMI IN will be set as a priority in this assignment. In this case, if you want to use the coaxial or optical audio input, make the appropriate selection in the “Audio Selector” (➔ page 47).

•Available sampling rate for PCM signals (stereo/mono) from a digital input (optical and coaxial) are 32/44.1/48/88.2/96 kHz/16, 20, 24 bit.

This section explains how to specify which speakers are connected and their sizes.

Cone diameter

For speakers with a cone diameter larger than 6-1/2 inches (16 cm), specify Large (full band). For those with a smaller diameter, specify Small (default crossover 100Hz). The crossover frequency can be changed in “Crossover (Crossover Frequency)”.

Note

•These settings are not available in either of the following cases:

–A pair of headphones is connected.

–The “Audio TV Out” setting is set to “On” (➔ page 49).

–“HDMI Ctrl (RIHD)” is set to “On” (➔ page 49) and you’re listening through your TV speakers.

■Subwoofer

`Yes

`No

■Front

`Small:

`Large:

Select based on the cone diameter.

Note

•If the “Subwoofer” setting is set to “No”, this setting is fixed to “Large”.

*1 If the “Front” setting is set to “Small”, the “Large” option cannot be selected.

■Crossover (Crossover Frequency)

This setting is advantageous for the speakers that you specified as “Small” in “Sp Config (Speaker Configuration)”. To get the best bass performance from your speaker system, you need to set the crossover frequency according to the size and frequency response of your speakers.

`40Hz, 50Hz, 60Hz, 70Hz, 80Hz, 90Hz, 100Hz, 120Hz, 150Hz, 200Hz

Use the diameter of the smallest speaker in your system when choosing the crossover frequency.

Speaker cone diameter	Crossover frequency
Over 8 in. (20 cm)	40/50/60 Hz*
6-1/2 to 8 in. (16 to 20 cm)	70/80/90 Hz*
5-1/4 to 6-1/2 in. (13 to 16 cm)	100 Hz
3-1/2 to 5-1/4 in. (9 to 13 cm)	120 Hz
Under 3-1/2 in. (9 cm)	150/200 Hz*

*Choose the setting matching your speaker.

To be continued

En-44