Advanced
4 | Use the Left and Right [ | ]/[ ] |
| buttons to adjust the speaker | |
| level, and use the Down [ | ] but- |
| ton to select the next speaker. | |
The level can be adjusted from
5 | Repeat step 4 so that the level of |
| |
| the test tone from each speaker |
| is the same. |
| Speakers that you set to No or None in |
| the Speaker Configuration (page 34) do |
| not output the test tone. |
|
|
6 | Press the [SETUP] button. |
| |
| Setup closes. |
| Don’t forget to turn down the volume if |
SETUP | you turned it up while setting the levels. |
| When you want to go back up one |
| menu level to “Level Cal,” press the |
| [RETURN] button. |
|
|
Note:
•A quicker way to adjust the speaker levels is to press the remote controller’s [TEST TONE] button to output the test tone, use the
•If the multichannel input is selected (page 37), in step 2, the “3. MultiLevel” menu appears instead of the “3. Level Cal” menu, and you can adjust the level of each channel of the multichannel input regardless of the Speaker Configuration settings.
You can adjust the volume of each speaker from – 12 dB to +12 dB
Digital Input Signal Formats
The following table shows the display indicators for each supported digital signal format.
Format | Display | |||||
|
|
|
|
|
|
|
Dolby Digital |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DTS |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PCM |
|
| PCM | |||
|
|
|
|
|
|
|
Normally, the AV receiver detects the signal format auto- matically. However, if you experience either of the fol- lowing issues when playing PCM or DTS material, you can manually set the signal format to PCM or DTS:
•If the beginnings of tracks from a PCM source are cut off, try setting the format to PCM.
•If noise is produced when fast forwarding or reversing a DTS CD, try setting the format to DTS.
|
|
|
|
|
|
| TUNING | / PRESET | MASTER VOLUME |
STANDBY/ON |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ENTER |
| |
| STANDBY |
|
|
|
|
|
|
|
|
A SPEAKERS B | TONE | + | STEREO | LISTENING MODE | DISPLAY DIGITAL INPUT | RT/PTY/TP MEMORY TUNING MODE | RETURN | SETUP |
|
|
|
|
|
|
| CLEAR |
|
PHONES |
|
|
|
|
|
|
|
MULTl CH | DVD | VIDEO 1/VCR | VIDEO 2 | VIDEO 3 | TAPE | TUNER | CD |
DIGITAL INPUT
1 | Press and hold the AV receiver’s [DIGITAL |
| INPUT] button for about 3 seconds. |
|
|
2 | While “Auto” is displayed (about 3 sec- |
| onds), press the [DIGITAL INPUT] button |
again to select: PCM, DTS, or Auto.
DTS or PCM: The DTS or PCM indicator, depending on which format you have set, flashes, and only signals in that format are output. Digital signals in other formats are ignored.
Auto (default): The format is detected automati- cally. If no digital input signal is present, the cor- responding analog input is used instead.
53
