Power for systems with a single amplifier can be supplied by most automotive electrical sys- tems. Systems with multiple amplifiers may require a higher capacity battery, alternator or the use of a storage capacitor. We strongly recommend the use of a Directed Audio Essentials power capacitor with an extra battery in larger stereo systems.

Orion amplifiers generate a certain amount of heat as part of normal operation. Be sure the area around the amplifier is unobstructed to allow adequate air circulation. Remember, beach blankets, last week's laundry, school books and homework papers located on top of the amplifier do not improve air flow and may become damaged.

Tools of the Trade

Listed below are the majority of the tools required to perform an installation. Having the proper tools will make the installation that much easier. Some of these tools are necessities; some will just make the job easier.

●Allen Wrenches (2.5mm and 3mm)

●DMM or VOM

●Electric drill with assorted drill bits

●Grommets

●Heat shrink tubing

●Marking pen

●Nylon tie straps

●Phillips and flat blade screw drivers

●Pliers (standard and needle nose)

●Reference CD with 1 kHz Sine Wave at 0dB level (all bits high)

●RTA (real time analyzer)

●Soldering iron and solder

●Utility knife

●Wire brush or sandpaper for chassis grounding

●Wire crimper

●Wire cutters

●Wire strippers

Step By Step Installation

Step 1 Determine the location for the amplifier. Refer to the Choosing Mounting Locations section of this guide for detailed information.

Step 2 Decide on the system configuration for your amplifier. For system sugges- tions, refer to the Speaker Connections section of this guide.

Step 3 Run all the wires from the amplifier location to the speakers, source unit, and battery. Do not connect the battery at this time. Be sure to run RCAs and power and speaker wires away from factory electrical wires and system as they pose a great potential for induced system noise.

Step 4 Pre-drill amplifier mounting holes. Be sure to "think before you drill". Gas tanks, fuel lines, and other obstructions have a nasty way of hiding them- selves. For best results use a marking pen to mark the mounting holes and pre-drill these holes with a standard 1/8" drill bit.

Step 5 Mount the amplifier. Make sure the amplifier is mounted on a flat surface. If this is not possible, do not over tighten the screws so that the chassis of the amplifier is twisted or bent.

Step 6 Turn the vehicle's key switch to the off position.

14

©2003 Directed Electronics, Inc.

Page 14 Page 16
Page 15
Image 15
Orion Car Audio 8002 manual Tools of the Trade, Step By Step Installation
Page 14 Page 16

8002 specifications

Orion Car Audio 8002 is a high-performance amplifier designed for car audio enthusiasts seeking powerful sound and exceptional clarity. This amplifier is renowned for its impressive output and efficient design, making it a top choice for those looking to enhance their in-car audio experience.

One of the standout features of the Orion 8002 is its robust power output. With a maximum output of 800 watts, this amplifier can easily drive multiple speakers and subwoofers, delivering a rich and immersive sound experience. It operates in a bridgeable configuration, allowing users to combine its channels for even more power, ideal for those who want to support larger, more demanding audio setups.

The Orion 8002 is equipped with advanced technologies that contribute to its superior audio quality. Its MOSFET power supply ensures efficient performance, reducing distortion and allowing for better dynamic range. This translates to clear, crisp highs and deep, resonant lows that bring music to life, making it suitable for a variety of music genres.

One of the key characteristics of the Orion 8002 is its versatile input options. It features both low-level RCA inputs and high-level speaker inputs, making it compatible with various head units and systems. This flexibility allows users to easily integrate the amplifier into their existing car audio system without the need for extensive modifications.

Additionally, the Orion 8002 comes with built-in crossover filters, providing users the ability to tailor the sound output to their specific needs. The adjustable high-pass and low-pass filters ensure that the amplifier can optimize performance according to the specific speakers or subwoofers being used.

The design of the Orion 8002 is not only functional but also stylish. Its sleek chassis is built to withstand the rigors of car environments, with a durable finish that complements any vehicle interior. Its compact size allows for straightforward installation in various locations within the car, ensuring users can find the perfect fit for their setup.

In conclusion, the Orion Car Audio 8002 amplifier combines powerful output, advanced technologies, and flexible features to deliver an outstanding listening experience. Whether upgrading an existing system or building a new one, the Orion 8002 stands out as a strong option for audiophiles seeking quality and performance in their car audio setup.
Top Page Image Contents