DPress TIMER. The VCR turns off automatically and “#” is displayed on the display panel.
24HR Quick Programing
You can program a timer recording that starts within 24 hours using the JOG dial on the VCR.
Load a cassette with the record safety tab intact. The VCR turns on, and the counter is reset, automatically.
DCancel or change program setting
To cancel a program, press CANCEL when the Program screen you do not want is shown.
To change a program, press the appropriate button:
EReturn to normal screen
APress 24HR QUICK PROGRAM on the VCR. “$” starts blinking on the display panel.
BTurn the JOG dial to the left or right to set the start time.
●One click stop of the JOG dial changes the time in
CPush the JOG dial. “” starts blinking on the display panel. Turn the JOG dial to the left or right to set the stop time.
●To set the tape speed, press SP/EP. The current setting for the tape speed appears on the display panel for about 5 seconds. Press SP/EP again to change the setting while tape speed is displayed.
Start time
Stop time
Channel number
Press PROG. CHECK repeatedly until no Program screen is shown.
FReengage timer recording standby mode
Press TIMER. The VCR turns off automatically and “#” is displayed on the display panel.
●When “AUTO TIMER” is set to “ON” ( pg. 15), the timer recording standby mode automatically resumes when you turn off the VCR.
Program overlap warning display
If “PROGRAM NOT COMPLETED PROGRAM OVERLAP” appears, you have another program overlapping the program you have just made. The Program Check screen appears and conflicting programs will start blinking.
DPush the JOG dial. Turn the JOG dial to the
left or right to select the channel, then press 24HR QUICK PROGRAM. The VCR turns off automatically and “#” is displayed on the display panel.
NOTES:
●If “Err” appears on the display panel, repeat the above steps again.
●When a menu screen is shown, you cannot use 24HR Quick Programing function. Press MENU to return to normal screen, and try again.
●You can use 24HR Quick Programing function also when the VCR is turned off.
●For 24HR Quick Programing function, the program overlap warning display does not appear even if some programs overlap each other.
To use the VCR while it is in timer recording standby mode
Press TIMER, then press POWER 1. After you use the VCR, press TIMER again to put the VCR into timer recording standby mode.
Checking, canceling or changing program settings
ADisengage timer
Press TIMER, then press POWER 1.
●When “AUTO TIMER” is set to “ON” ( pg. 15), you do not have to press TIMER.
B Access Program Check screen | PR START | STOP | CH | DATE | |
Press PROG. CHECK. | 1 | 8:00P | 10:00 | 12 | 12/24 |
2 | 10:00A | 10:45 | 40 | 12/25 | |
C Access Program screen | 3 | 11:30P | 1:00 | 125 | 12/25 |
4 |
|
|
|
| |
5 |
|
|
|
| |
Press PROG. CHECK again. Each time you | 6 |
|
|
|
|
7 |
|
|
|
| |
press PROG. CHECK, the next program’s | 8 |
|
|
|
|
| PRESS (CHECK) TO NEXT |
| |||
Program screen appears.
| PR START | STOP | CH | DATE | ||
PROGRAM NOT COMPLETED | 1 | 8:00P | 10:00 | 12 | 12/24 |
|
2 | 10:00A | 10:45 | 40 | 12/25 |
| |
PROGRAM OVERLAP | 3 | 11:30P | 1:00 | 125 | 12/25 |
|
4 | 9:00P | 10:00 | 10 | 12/24 |
| |
| 5 |
|
|
|
|
|
| 6 |
|
|
|
|
|
| 7 |
|
|
|
|
|
| 8 |
|
|
|
|
|
| ( | , ) THEN ( ) (PROG.) : END | ||||
Example:
Program 1 (you have just made) and Program 4 overlap each other
A Select program to modify
Press rt, then press OK or e.
● You can only select one of the overlapping programs.
● If you do not mind this overlap, press
PROG. to finish the timer program setting. The program starting earlier or
program with the lower program number will be recorded.
B Cancel or change program setting |
| PROGRAM 4 |
To cancel a program, press CANCEL when | START | STOP |
the Program screen you do not want is | 9:00PM | 10:00PM |
DATE | CH | |
shown. | 12/24/02 | 10 SP |
TUE |
| |
To change a program, press the |
| |
PRESS (CANCEL) TO CANCEL | ||
appropriate button: | PRESS (OK) TO CONFIRM | |
PRESS (PROG.) TO END | ||
|
| |
key “8”), WEEKLY (Number key “9”) and/or SP/EP when the Program screen on which you want to make changes is shown, then press OK or e.
●If the overlap is not yet solved, the conflicting programs will be shown on the Program check screen. Repeat the above steps again.
— 13 —
