Panasonic AG-DVC60 manual Recording Setup screen, Description of settings Mode

SW MODE screen

Item/
(Display		Description of settings
mode)
FOCUS	Use this to select the function to be allocated
RING	to the focus ring.
(CAM)	ZOOM:
	Zooming can be performed using the
	focus ring when the camera-recorder is
	operated in the auto focus mode.
	IRIS:
	Iris adjustments can be performed using
	the focus ring when the camera-recorder
	is operated in the auto focus mode and
	the iris is to be adjusted manually.
	OFF:
	The focus ring is used to perform manual
	focus adjustments only.
IRIS DIAL	Use this to set how the iris is to be controlled
(CAM)	by the direction in which the multi dial is
	rotated when the iris is to be adjusted manu-
	ally.
	DOWN OPEN:
	The iris opens when the multi dial is
	turned downward.
	UP OPEN:
	The iris opens when the multi dial is
	turned upward.
ZOOM	Use this to set the speed of the motordriven
MODE	lens zoom. (P31)
(CAM)	NORM	: Standard
	HIGH	: High speed
	LOW	: Low speed
HANDLE	To select the HANDLE ZOOM switch. (P31)
ZOOM (CAM)	L/OFF/H, L/M/H
HANDLE S/S	Use this to set whether the recording opera-
INHIBIT	tion is to be performed using the START/
(CAM)	STOP button on the lens.
	OFF:
	Recording is permitted.
	ON:
	Recording is inhibited so as to prevent
	operation from being conducted by mis-
	take.
SNS (CAM)	Use this to select the high-sensitivity shooting
	mode. (P32)
	IR, SUPER_IR, COLOR_NS
SNS SET MEM	To select whether to record the SNS mode.
(CAM)	OFF:
	The mode is not recorded.
	ON:
	The mode is recorded.
D. ZOOM	Use this to select the magnification level for
(CAM)	the digital zoom. (P31)
	x24, x160

RECORDING SETUP screen

Item/
(Display		Description of settings
mode)
REC SPEED	Use this to select the recording duration
(CAM) (VCR)	mode.
	SP : SP (standard recording) mode.
	LP : LP (long recording) mode.
AUDIO REC	Use this to select the digital audio recording
(CAM) (VCR)	system.
	32K (12bit):
		The sound is recorded using the 12-bit/32
		kHz (4 channels) recording system.
		Select this mode when leaving the sound
		heard during shooting intact even when
		audio dubbing is performed on an existing
		recording.
	48K (16bit):
		The sound is recorded using the 16-bit/48
		kHz (2 channels with a good sound qual-
		ity) recording system.
		The sound heard during shooting will be
		erased when dubbing over an existing
		recoding.
WIND CUT	Select ON to reduce the noise generated by
(CAM) (VCR)	the wind blowing into the microphone in
	windy conditions. Effective with FRONT and
	REAR (LINE/MIC) input.
	OFF, ON
ID SET	Use this to set the ID (5 characters) informa-
(CAM)	tion. The ID information set is displayed when
	the color bar mode is established.
	•	Characters which can be set:
		(space), A to Z, 0 to 9, ., /, :
TIME STAMP	Set this to REC to record the date and time
(CAM)	that were selected using the DATE/TIME set-
	ting item (P71) on the DISPLAY SETUP
	screen as an image on the tape.
	NO-REC, REC
1394 TC	Use this to select the time code to be
REGEN	recorded when recording the signals of the
(VCR)	unit connected to the DV connector.
	OFF:
		The time code that was selected using the
		TCG setting item and FIRST REC TC set-
		ting item is used for the recording.
	ON:
		The time code of the signals which are
		input to the DV connector are used for the
	•	recording.	MENUS
		takes precedence over the TCG item and
		When ON has been selected for this item,
		the time code of the signals concerned
		FIRST REC TC item settings.
	•	If no signals are input to the DV connector,
		the TCG item and FIRST REC TC item
		settings are used.

The underlining indicates the factory setting.

69