Panasonic AJ-SD255E manual 24

Setup menus (continued)

USER menu <OPERATION>

No./Item		Description
114	This selects whether to cause the REC
	INH lamp to flash or light up when the
REC INH	cassette has been set to the accidental
LAMP	erasure prevention status.
	0000	LIGHT : The lamp lights up.
	0001	FLASH : The lamp flashes.
	Note:
	When the REC INHIBIT switch is set to
	ON, the REC INH lamp always lights
	regardless of the general setting status.
115	This selects whether to enable or
	disable the operation of the EJECT
EJECT SW	button on the front panel.
INH	0000	REC :
	Operation is disabled while the unit is
	in the recording mode.
	0001	OFF :
	Operation is enabled in all modes.
120	This selects the modes for the picture
	and sound output when the tape is
EJECT EE SEL	ejected.
	0000	EE : EE mode
	0001 BLACK :
	The picture turns black, and the sound
	is muted.
	0002	GRAY :
	The picture turns gray, and the sound
	is muted.
	Note:
	The IEEE1394 digital output video will be
	black even if GRAY is selected.
121	This selects whether the EE mode or
	playback mode is to be established
F/R EE SEL	during fast forwarding or rewinding.
	0000	EE : EE mode
	0001	TAPE : Playback mode
122	This select whether the EE mode or
	playback mode is to be established
STOP EE SEL	when operation is stopped.
	0000	EE : EE mode
	0001	TAPE : Playback mode
	Note:
	The selection is complied with even in the
	standby OFF mode. However, the picture
	will turn gray (black for IEEE1394 digital
	output) when TAPE is selected.

The underlined items indicates the initial setting.

No./Item		Description
160	This sets the repeat play mode.
MEMORY	0000	OFF :
MODE	No repeat play (normal operation)
	0001 M-STOP :
	The tape stops near the BEGIN point when a
	FF or REW operation has been performed.
	0002	REPT1 :
	During playback, the tape is rewound
	to the BEGIN point and stopped when
	the END point is reached.
	0003	CONT :
	During playback, the tape is rewound
	to the BEGIN point and then played,
	and these steps are repeated when
	the END point is reached.
161	This sets the BEGIN point in the repeat
	play mode.
CTL BGN	Whether TC or CTL is displayed on the counter
or
TC BGN	when the COUNTER button is pressed is set
	here. When there is no setting, --:--:--:-- appears,
	and the tape start serves as the BEGIN point.
162	This sets the END point in the repeat
	play mode.
END	Whether TC or CTL is displayed on the counter
	when the COUNTER button is pressed is set
	here. When there is no setting, --:--:--:-- appears,
	and the tape end serves as the END point.
163	This sets the output image when the
	tape returns to the BEGIN point in the
REPT MODE	repeat play mode.
	0000 FREEZE :
	The tape returns to the BEGIN point
	while the playback image at the END
	point remains frozen.
	0001	BLACK :
	The tape returns to the BEGIN point while
	a BLACK picture remains on the screen.
	0002 EE_SEL :
	The tape returns to the BEGIN point
	with an image which is in compliance
	with the setup menu item No.121 (F/R
	EE SEL) setting.
	Note:
	If, when FREEZE has been selected, the
	END point has been set at the tape end,
	the playback image will not be frozen
	properly. Set the END point in a range
	where pictures have been recorded.

USER menu <INTERFACE>

No./Item		Description
202	This sets the ID information to be
	returned to the controller.
ID SEL	0000	OTHER :
	0001 DVCPRO :
	0002	ORIG :
	Notes:
	• ID information of any VTR except for the
	DVCPRO’s is set in OTHER.
	• The ORIG setting should only be used
	when a Panasonic controller (AG-A850
	etc. sold separately) is connected.

24