Panasonic CQ-C9901U, CQ-C9801U, C9701U operating instructions Radio

Radio

You can assign your favorite broadcasting station to the
[D•M] button. As the result of doing that, your favorite
broadcasting station can be received even if the CD mode	SRC	CS
or the CD changer mode is activated. (Default: FM 87.9
MHz)

		Note: For the use of an FM transmitter, it is useful
		for users to register applicable frequencies on D•M
MemoryDirect	Memory)Direct(D•M:	(Direct Memory).
		D•M station calling
		1 Press [D•M] (Direct Memory).
		D•M station writing
		1 Select a station you would like to preset.
		Lights when the D•M mode is activated.
		2 Hold down [D•M] (Direct Memory) for
		2 sec. or more.

	Up to 6 stations can be preset in AM, FM1, FM2, and FM3	Manual station preset
	respectively.
		1 Tune in to a station.
	Preset stations can be simply called up by pressing [}]
	(P·SET) or [{] (P·SET).	2 Hold down [}] or [{] for 2 sec. or
	Notes:
	¡ Direct Access can be executed with [1] to [6] buttons		more.
	on remote control.	3 Select a preset number by pressing [}]
	¡ You can switch between 6 and 18 for FM presetting
Preset)	stations. (a page 23)		or [{].
	¡ Preset stations are changeable. (a page 23)	4 Preset the station by holding down [}]
	Auto Preset Memory (APM)
Station Preset Auto Preset Memory, P·SET:			or [{] for 2 sec. or more.
	Stations with good receiving conditions are automatically
	preset.
	1 Select a band.
	2 Hold down [BAND]		Frequency/preset number blinks once.
	(APM) for 2 sec.	Notes:
	or more.	¡ New stations overwrite existing saved stations.
(APM:	The preset stations under best receiving conditions	¡ In step 2, a station can be registered by holding down
		the numeric button [1] to [6] for 2 sec. or more.
	are received for 5 sec. each after presetting the sta-	¡ To stop presetting stations, press [DISP] (Display).
	tions (SCAN). To stop scanning, press [}] or [{].

Note: New stations overwrite existing saved stations.

Mono/Local Setting (Radio Menu Display)

(MONO/LOCAL)

In the AM mode, only NOISE SUPPRESSION and LOCAL can be selected.

1 Press [MENU] to

display the menu display.

For using the remote control, hold down [MENU] for 2 sec. or more.

2 Press [}] or [{] to select a mode to be adjusted.

3 Press [BAND]

(SET) to adjust.

4 Press [MENU] to confirm the adjust- ment.

For using the remote control, hold down [MENU] for 2 sec. or more.

MONO (Monaural)

Noise reduction when the signal strength decreases

: Receiving in stereo (default)

: Receiving in mono and reducing the noise level

LOCAL

Setting when searching for a station

: Searching even for a relatively low-intensity radio wave station (default)

: Searching only for a high-intensity radio wave station

NOISE SUPPRESSION

IF filter setting for noise suppression	English
: Narrow range
: Wide range
: Middle range (default)

AUTO PRESET

You can select 6 or 18 stations for FM presetting with the use of APM.

:

Presets 6 stations to FM1 to FM3 respectively, that is, 18 stations in total at the same time. This function is useful for presetting more than 6 stations. (default)

:

Presets 6 stations with good reception to the selected band from FM1 to FM3. This function is useful for preset- ting stations in different areas in different bands.

PRESET EDIT
	Radio
You can arrange the order of the preset stations. Preset
stations can be reordered as you like after executing APM
or the like.

1 Press [}], [{], []] or [[] to select one station to be interchanged.

2 Press [BAND] to confirm your selection. 3 Press [}], [{], []] or [[] to select the

other station to be interchanged.

4 Press [BAND] to confirm your selection.

●Calling an FM station registered on D•M.

RADIO AUDIO FILTER

You can select the reception status (band) of FM stations registered on D•M.

: OFF (default)

: High cut level 1 : High cut level 2

22 CQ-C9901U/C9801U/C9701U CQ-C9901U/C9801U/C9701U 23