Panasonic CQ-R223W manual Remote Control, Battery Installation, Preparation, Battery Notes

Models: CQ-R223W

1 35
Download 35 pages 48.22 Kb
Page 11
Image 11
Remote Control
182 mm
53 mm

G

 

Remote Control

 

 

E

 

 

 

 

N

 

 

 

 

L

 

 

 

 

 

Battery Installation

 

 

S

 

 

 

I

 

 

 

 

H

 

Remove the battery holder.

Lithium battery

9

 

(Back side) (included)

 

Press and hook A of the battery holder and then pull it out.

 

 

 

 

 

 

 

 

 

 

 

Installation

 

 

 

 

 

 

E

 

 

 

 

 

 

N

 

 

 

 

 

 

G

 

 

 

 

 

 

 

L

 

 

Installation Hardware

 

 

 

Preparation

 

 

 

 

I

 

 

 

 

S

 

 

 

 

 

 

 

H

• Before installation, check the radio operation with

 

No.

Item

Diagram

Q’ty

 

 

 

10

antenna and speakers.

 

q Mounting Collar

 

1

 

 

 

 

 

 

 

 

 

 

Install the battery on the battery holder.

Set a new battery properly with its “+” side facing up as shown in the figure.

Insert the battery holder.

Push the battery holder back into its original position.

Position B

Battery holderBattery InstallationRemove the battery holder.Installation Position A

• Disconnect the cable from the negative (–) battery

 

 

 

terminal (see caution below).

 

 

 

• Unit should be installed in a horizontal position with

w Hex. Nut (5 mmø)

1

the front end up at a convenient angle, but not more

 

 

 

than 30°.

e Rear Support Strap

1

 

30˚ or less

r

Tapping Screw

1

(5 mmø 16 mm)

Battery Notes

Remove and dispose of an old battery immediately.

Battery Information:

Battery type: Panasonic lithium battery (CR2025) (included)

Battery life: Approximately 6 months with normal use (at room temperature)

Caution: Improper use of batteries may cause overheating, an explosion or ignition, resulting in injury or a fire. Battery leakage may damage the unit.

 

t Mounting Bolt (5 mmø)

1

Caution: Do not disconnect the battery terminals of

y Power Connector

1

a car with trip or navigational computer since all

 

 

user settings stored in memory will be lost.

u Dismounting Plate

2

Instead take extra care with installing the unit to

prevent shorts.

 

 

 

i Trim Plate

1

Dashboard Installation

Do not disassemble or short the battery. Do not throw a battery into a fire.

Keep batteries away from children to avoid the risk of accidents.

Be careful to observe proper local disposal rules when you dispose of batteries.

Control Reference Guide

Buttons of the remote control function in the same way as the controls on the main unit of the reference page.

Point the remote control unit at the main unit’s sensor (REMOTE).

Installation Opening

The unit can be installed in any dashboard having

an opening as shown at right. The dashboard

should be 4.5 mm - 6 mm thick in order to be able to support the unit.

Installation Precautions

(a) Using the Rear Support Strap

r Tapping Screw

Fire Wall of Car

 

 

 

(ATT)

[PWR] (power)

PWR

MUTE

DOLBY B NR

[MUTE] (Mute) (page 12)

REMOTE

This product should be installed by a professional installer, if possible.

In case of difficulty, please consult your nearest authorized Panasonic Service Center.

w Hex. Nut

e Rear Support Strap

[MODE] (Mode (source))

 

 

MODE

 

 

(page 14, 18)

 

 

 

 

VOL

[BAND] [DISC

UP]

 

PRG

BAND/DISC UP

 

 

(Band/Disc change/play

 

 

 

 

 

side change)

 

 

TUNE

(page 14, 18)

 

 

TRACK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Car Audio

TUNE

TRACK

[VOL] [}] [{] (Volume) (Volume Up/down)

(page 12)

[TUNE][TRACK] [a] [ ] []] [[] (Tune/track, selection/search/Fast forward/Fast reverse)

(page 14, 18)

1.This system is to be used only in a 12-volt, DC battery system (car) with negative ground.

2.Follow the electrical connections carefully (a page 25). Failure to do so may result in damage to the unit.

3.Connect the power lead (red) after all other connections are made.

4.Be sure to connect the battery lead (yellow) to the positive terminal (+) of the battery or fuse block (BAT) terminal.

5.Insulate all exposed wires to prevent short circuiting.

6.Secure all loose wires after installing the unit.

7.Please carefully read the operating and installation instructions of the respective equipment before connecting it to this unit.

t Mounting Bolt

q Mounting Collar

(b) Using the Rubber Cushion (option)

Rear Support Bracket (Provided on the car)

Rubber Cushion (Option)

t Mounting Bolt

q Mounting Collar

20

CQ-R223W

CQ-R223W

21

Page 11
Image 11
Panasonic CQ-R223W manual Remote Control, Battery Installation, Preparation, Battery Notes, Control Reference Guide