Panasonic GN SERIES 3.8.2 Connecti ng to the DC Power Supply ,

Product Description

GN Series Hardware Manual

4. Lift the cover, for example with a screwdriver, to access the terminal screws

5. Turn the terminal screws counter-clockwise to loosen

6. Insert the wires into the corresponding terminals

Make sure that the polarity is correct!

7. Turn the screws clockwise to tighten

8. Close the cover

9. Prepare the other end of each wire for connection to the DC power supply

3.8.2 Connecti ng to the DC Power Supply

Connect the GN panel to a DC power supply using the DC power plug and a corresponding

cable (see page 34).

The DC power supply must be able to output 50W to cope with the inrush current.



NOTE

• The DC power supply should be able to be switched off and on via an

isolating switch.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.ctiautomation.net - Email: info@ctiautomation.net

Contents

Main Asia Pacific JapanNorth America Europe Global Network Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.ctiautomation.net - Email: info@ctiautomation.net GN Series Hardware Manual BEFORE BEGINNING LIMITED WARRANTY Important Symbols DANGER! Table of Contents 1. Introduction ............................................................................1 2. Scope of Delivery ...................................................................9 3. Product Description .............................................................13 4. Technical Data...................................................................... 43 5. Index...................................................................................... 57 Page Page 1.1 Safety Instructions Page 1.2 Overview 1.3 Electrostatic Discharge (ESD) 1.3.1 Grounding Methods 1.4 FCC Statement 1.5 Electromagnetic Compatibility 1.6 Applicable Directives and Standards Page 2.1 Product Parts 2.2 Type Label and Product Identification Page Page 3.1 All Views Page 3.2 Front View 3.2.1 USB Interface on the Front 3.2.2 Front Plates 3.2.3 Display with Touch Screen 3.2.4 Calibrating the Touch Screen 3.2.4.1 Calibration under Windows XP Page Page 3.2.4.2 Calibration under Windows XP Embedded 3.2.5 Touch Screen Care and Cleaning 3.3 Bottom View 3.3.1 Optional Interfaces 3.3.1.1 RS422/RS485 Serial Interface Page 3.3.2 DC Power Connector 3.3.3 LAN0 and LAN1 Ethernet Interface Connectors 3.3.4 VGA Interface Connector 3.3.5 Reset Button 3.3.6 Status LEDs 3.3.7 Grounding Screw (M4) with Lock Washers 3.4 Top View 3.4.1 Compact Flash Card Slot 3.5 Left and Right Side View Page 3.6 Rear View Page Page 3.8 Connecting the System to the Power Supply 3.8.1 DC Power Plug 3.8.2 Connecti ng to the DC Power Supply Page 3.9 Mounting the System to a Subframe or Panel Page Page 3.10 Accessing Internal Components 3.10.1 Configuration of the RS422/RS485 Port Page 3.10.2 Replacing the Lithium Battery WARNING Page Page 4.1 General Specifications GN series GN07 GN10 GN12 GN15 Page 4.2 Environmental Specifications 4.3 Dimensions 4.3.1 Front Views Page 4.3.2 Rear and Right Side Views Page Page Technical Data GN Series Hardware Manual 52 4.4 Pin Assignments In this section you can find the pin assignments for the standard interfaces. 4.4.1 Ethernet Interfaces (LAN0 and LAN1) Pin No. Signal name RJ45 (female) connector 4.4.2 USB Interfaces 4.4.4 RS422/RS485 Configured as RS422 (4-Channel Mode) Use the DIP switches to configure the interfaces (see page 23). Pin Signal short name Long name 9-pin Sub-D plug (female) 4.4.5 RS422/RS485 Configured as RS485 (4-Wire Mode), Full Duplex, Bus Master Use the DIP switches to configure the interfaces (see page 23). 4.4.7 VGA Port (VGA) Pin Signal name 15-pin Sub-D-Plug (female) 1 15 11 5 10 6 4.4.8 DC Power Connector 4.5 Cables Type of communication Description Product no. ** RS232 connection cable wiring ** * * * Index Page Page Record of Changes Manual No. Date Description of Changes