Be redialled correctly | Panasonic KX-TG2551ALS, KX-TG2551NZS

Troubleshooting

Problem

Cause & Remedy

The handset display goes to the standby mode while viewing the Caller List.

•Do not pause for over 60 seconds while searching.

(HANDSET!LOCATOR) does					•The handset is too far from the base unit.
not function.					•The handset is engaged in an outside
					call or is viewing the Caller
					List/directory list. Wait until the IN
					USE/CHARGE indicator light goes out.

You cannot redial by					•If the last number dialled was more
pressing (REDIAL/PAUSE).					than 32 digits long, the number will not
					be redialled correctly.
					•The button has a double function as
					either redial or pause. It will redial the
					last number dialled if pressed at the
					outset of a call (p. 18). If another
					number has been dialled ﬁrst, it will
					operate as a pause button (p. 40).

“Recharge” is displayed on •Charge the battery fully (p. 11).
the handset, “				” ﬂashes


or the unit beeps
intermittently.

You charged the battery fully, but “Recharge” is still

displayed and/or “ ” continues to ﬂash.

•Clean the charge contacts and charge again (p. 12).

•Install a new battery (p. 47).

The IN USE/CHARGE	•This is normal.
indicator light does not go
out after the battery has
been charged.

You cannot have a	•When the headset is connected (p. 46),
conversation using the	you must use the headset to talk with
handset.	the caller. To have a normal cordless
	phone conversation, disconnect the
	headset.

You cannot have a	•Make sure that the headset is
conversation using the	connected properly (p. 46).
headset.	•Please use only the Panasonic

KX-TCA88AL headset.

50

Image 50

Panasonic KX-TG2551ALS, KX-TG2551NZS Handset is too far from the base unit, Than 32 digits long, the number will not

Contents

Charge the battery for about 6 hours before initial use Operating Instructions For your future reference Accessories includedBefore Initial Use Base Unit Location/Noise Battery ChargeFor Best Performance Contents Useful Information Call Waiting and Caller ID Compatible For Australia only Handset How to use the Navigator keyLocation of Controls Base unit Caller ID Indicator pIndicator p Hook p Antenna p Charge Contacts p Display 0266667777 0355566677 1120A JAN10 Settings Connections Fully charged Medium Low ﬂashing Needs to be recharged Battery strengthDisplay prompt Battery strength Recharge Battery informationStandby mode While the handset is off the base unit Operation Operating time Selecting the Line Mode During programming Programmable FunctionsLCD contrast To select the LCD contrast p Setting the Auto Talk Feature Press Ö or Ñ to select On or Off Selecting the Ringer Volume To turn the ringer ON, press Ñ or Ö Press Ö or Ñ to select the desired Selecting the LCD ContrastPoints to LCD contrast Contrast To redial the last number dialled Making CallsIf noise interferes with the conversation To increase, press Ñ To decrease, press Ö To dial after conﬁrming the entered numberTo redial after conﬁrming the last number dialled Lighted handset keypad Answering CallsAuto Talk Backlit LCD display Private name display Caller ID ServiceHow caller information is displayed when a call is received While the handset is on the base unit To check the number of new callsFor New Zealand Users While the handset is off the base unit Using the Caller List Viewing the Caller List To exit the Caller List Ex. When you search from the most recent callTo return to the previous caller Display meaning Press Ö or Ñ to enter the Caller List Calling Back from the Caller ListLift the handset off the base unit Press Ö or Ñ repeatedly to ﬁnd Free editing Editing the Caller’s Phone NumberYou can edit a phone number in the Caller List When the caller’s name is not displayed in the Caller List Storing Caller List Information in the Directory Erasing Caller List Information To erase a speciﬁc caller from the Caller List To erase all entries in the Caller List One-Touch Dialler Storing a Phone Number in the Direct Button Dialling the Stored Number in the Direct Button Using the Directory Storing Names and Numbers in the Directory Enter a name, up to 15 characters using Dialling buttons p Number of times key is pressed Keys Selecting Characters to Enter NamesIf you make a mistake while entering a name While the arrow points to Save When ﬁnished, press Ö Next keyFor example, to enter Tom Jones Eight times Finding Items in the Directory To search for a name by initial Keys Index Dialling from the DirectoryIndex table Editing an Item in the Directory Press FWD/EDIT á Yes key or Clear Erasing an Item from the DirectoryDirectory item you want to erase Automatic Security Code Setting Special FeaturesHow to Use the Pause Button Handset Locator For Australia only For Call Waiting Service Users in New ZealandCall Waiting and Caller ID Compatible Points to Recall time Recall ButtonSelecting the recall time Desired time is displayed Adding Another Phone Wall mounting adaptor, then Wall MountingTuck the telephone line cord inside Push it in the direction of the arrow To charge the handset battery To attach the belt clip To remove the belt clip Using the Belt ClipUsing an Optional Headset Connection an optional headset to the handset Battery strength prompt correctly p Battery ReplacementThen install the new one Few minutes Troubleshooting Problem Try again Have been pressed when you picked upHandset. Press FUNCTION/EXIT/CH Than 32 digits long, the number will not Recharge is displayed on Charge the battery fully pHandset is too far from the base unit Be redialled correctly For Australian Customers For New Zealand Customers Installations Environment Safety InstructionsSafety Placement Medical Speciﬁcations Instructions to customer InstallationImportant Information For Australia only Service difficulties PQQX13462ZA-BM S0802-0