Panasonic PT-47WX34 Set Up, ˆ Converge, Convergence ADJ, Nine Point Convergence Correction

ICON MENUS OPERATION

SET UP (cont.)

ˆCONVERGE (cont.)

Note: After selecting, press VOL to activate RESET TO DEFAULT feature. When using this feature in Zoom mode, the effect can only be verified when you exit all menus and display normal picture.

SET UP

CONVERGE. CONVERGENCE ADJ.

RESET TO DEFAULT

PRESS ACTION TO RETURN

CONVERGENCE ADJ.

Procedure

•After pressing VOL the align Green to Center screen will be displayed.

•Then use the navigation buttons on the remote control to align the horizontal and vertical green lines on screen, with the cabinet reference marks on top center and left

center of cabinet, as shown below.

Reference Marks

		PRESS CH AND VOL KEY TO
		ALIGN GREEN LINES TO THE
	CENTER MARK ON THE CABINET
			UP
		LEFT	RIGHT
			DOWN
Front of cabinet		PRESS ACTION TO CONTINUE

•Press ACTION to display red center correction screen.

•Use the navigation buttons on the remote control to align the red cross with the white cross pattern at the center of the screen.

Note: To prevent picture tube damage, do not leave test pattern on for an extended period of time.

•Then press “0” on the remote control keypad to display the BLUE center correction screen, repeat procedure for adjusting blue. If needed press “0” again to return to RED correction screen.

Note: An adjusted cross pattern appears white with a minimum of color protrusion.

IF RED IS PROTRUDING FROM					IF BLUE IS PROTRUDING FROM
CENTER CROSS, PRESS CH AND					CENTER CROSS, PRESS CH AND
VOL KEY TO CORRECT				Press	VOL KEY TO CORRECT
		UP			UP
				“0”
	LEFT		RIGHT		LEFT	RIGHT
		DOWN			DOWN
PRESS 0 TO ADJUST BLUE					PRESS 0 TO ADJUST BLUE
PRESS ACTION TO CONTINUE					PRESS ACTION TO CONTINUE

NINE POINT CONVERGENCE CORRECTION

Note: Remote Control must be in TV mode.

Procedure

•Press ACTION to display red correction screen.

•Press the 1 through 9 keypad buttons on the remote control to select the desired convergence position.

•Use the navigation buttons to align the RED cross with the white cross pattern.

Note: An adjusted cross pattern appears white with a minimum of color protrusion.

1	2	3
PRESS # KEY TO SELECT POS.
PRESS CH AND VOL KEY TO CORR.
4		6
	CORRECTING RED
	PRESS 0 TO ADJUST BLUE
	PRESS ACTION TO EXIT
	PRESS ACTION TO EXIT
7	8	9

•Press “0” on the remote control keypad to display the BLUE correction screen, then repeat procedure.

1	2	3		1	2	3
PRESS # KEY TO SELECT POS.				PRESS # KEY TO SELECT POS.
PRESS CH AND VOL KEY TO CORR.			Press	PRESS CH AND VOL KEY TO CORR.
4		6		4		6
			“0”
	CORRECTING RED				CORRECTING BLUE
	PRESS 0 TO ADJUST BLUE				PRESS 0 TO ADJUST RED
	PRESS ACTION TO EXIT				PRESS ACTION TO EXIT
	PRESS ACTION TO EXIT				PRESS ACTION TO EXIT
7	8	9		7	8	9
•	To exit press ACTION repeatedly, then press CH .

ˆOTHER ADJ.

Highlight OTHER ADJ. and press VOL to enter sub sub- menu field.

Note: While sub sub-menu features are highlighted, press VOL to adjust or activate.

SET UP
MODE	CABLE ￿
AUTO PROGRAM	￿
MANUAL PROGRAM	￿
AUTO POWER ON	OFF
OTHER ADJ. CHAN BANNER	ON
IMAGE SHIFT	ON

PRESS ACTION TO RETURN

•MODE - To select TV (antenna) or CABLE mode depending on the signal source.

•AUTO PROGRAM - To automatically program all channels received through the RF input.

•MANUAL PROGRAM - To manually add or delete channels.

•AUTO POWER ON - Select SET to power up the TV at the same time as the Cable box or other components or select OFF.

•CHAN BANNER - Select ON to display onscreen banner when changing channels.

•IMAGE SHIFT - Selecting ON is recommended for this feature to prevent image retention on screen.

ENGLISH

29z