Using the SERIAL connector
The serial connector which is on the connector panel of the projector conforms to the
Control commands
Command | Control | Remarks | |
Contents | |||
|
|
Connection
SERIAL(female)Computer
DIN
Serial adapter
NOTE:
BYou must use only
Pin assignments and signal names
| 1 | 2 | |
| 3 | 5 | |
| 6 | 8 | |
| DIN | ||
| Appearance | ||
Pin | Signal | Contents | |
No. | name | ||
| |||
% | RXD | Received data | |
& | GND | Earth | |
' | TXD | Transmitted data | |
# |
|
| |
$ |
| Connected internally | |
( |
|
| |
) |
| NC | |
* |
| NC |
Communications settings
Signal level | |
Sync. method | Asynchronous |
Baud rate | 9 600 bps |
Parity | None |
Character length | 8 bits |
Stop bit | 1 bit |
X parameter | None |
S parameter | None |
Basic format
The data sent from the computer to the projector is transmitted in the format shown below.
STX Command : Parameter ETX
|
|
|
|
|
|
| |
Start byte |
| 1 byte | End byte | ||||
(02h) | 3 bytes | 1 | bytes (03h) |
NOTE:
BThe projector can not receive the command for 10 seconds after the lamp is switched on.
Wait 10 seconds before sending the command.
BIf sending multiple commands, check that a response has been received from the projector for one command before sending the next command.
BWhen a command which does not require parameters is sent, the colon (:) is not required.
BIf an incorrect command is sent from the personal computer, the “ER401” command will be sent from the projector to the personal computer.
|
| In standby mode, all commands other than |
| |||
PON | Power ON | the PON command are ignored. |
| |||
BThe PON command is ignored during |
| |||||
|
|
| ||||
|
| lamp ON control. |
|
|
| |
|
| BIf a PON command is received while the |
| |||
|
|
| ||||
|
| cooling fan is operating after the lamp |
| |||
POF | Power OFF | has switched off, the lamp is not turned |
| |||
back on again straight away, in order to |
| |||||
|
|
| ||||
|
| protect the lamp. |
|
|
| |
|
|
|
|
|
| |
|
| Parameter |
|
|
| |
IIS | Input signal | VID=VIDEO |
| |||
selection | RG1=PC | YUV=YPBPR |
| |||
|
| |||||
|
| SCT=SCART | HDM=HDMI |
| ||
|
|
|
|
| ||
|
| Operation will be switched between ON and |
| |||
OSH | Shutter function | OFF each time the command is sent. Do |
| |||
not switch operation ON and OFF after only |
| |||||
|
|
| ||||
|
| short periods of time. |
|
|
| |
|
|
|
|
| ||
|
| The picture being projected will be paused. |
| |||
OFZ | Freeze function | Parameter |
|
|
| |
|
| 0=ON | 1=OFF |
| ||
|
|
|
|
| ||
OMN | Menu screen | The menu screen will be displayed. |
| |||
|
|
|
|
| ||
OEN | ENTER | Use this command to accept and to activate |
| |||
items selected in the |
| |||||
|
|
| ||||
|
|
|
|
| ||
OBK | RETURN | Use this command to return to a previous |
| |||
menu screen or to clear the menu screen. |
| |||||
|
|
| ||||
|
|
|
|
|
| |
OCU |
| OCU= F button |
|
|
| |
OCD | F, G, I and H | OCD= G button |
|
|
| |
OCL | buttons | OCL= I button |
|
|
| |
|
|
| ||||
OCR |
| OCR= H button |
|
|
| |
|
|
|
|
| ||
OVM | MAIN | Use this command to display an item in the |
| |||
“PICTURE” menu. (page 35) |
| |||||
|
| Others | ||||
|
|
|
|
| ||
|
| Parameter |
|
| ||
| Picture mode | NAT=NATURAL | NOR=NORMAL | |||
VPM | DYN=DYNAMIC | CN1=CINEMA1 | ||||
selection | ||||||
| CN2=CINEMA2 | CN3=CINEMA3 |
| |||
|
|
| ||||
|
| VID=VIDEO |
|
|
| |
|
|
|
|
| ||
|
| (Continued on next page.) |
| |||
|
|
|
|
|
|