<Projector control panel and remote control unit>
# $ % | & | ' ( | ) |
|
|
| |
|
|
|
| & |
|
| ) |
|
|
|
| ( | POWER | INPUT | |
|
|
|
|
|
| ||
|
|
|
|
| VIDEO RGB | , | |
RGB INPUT LAMP | TEMP |
| POWERAUTO SETUP | INPUT+ | AUTO | MENU | |
|
|
|
| SETUP | * | ||
|
|
|
| - |
|
| |
|
|
|
|
| ENTER | 2 | |
|
|
| STANDBY(R) | . |
|
| |
|
|
| ON(G) | FREEZE | SHUTTER | ||
|
|
|
|
|
|
| 1 |
|
|
|
|
|
| STD |
|
|
|
| MENU | ENTER | VOLUME | D.ZOOM |
|
|
|
|
|
|
| INDEX |
|
|
|
|
|
|
| WINDOW |
|
|
|
|
| / |
| PROJECTOR | 0 |
,+ *
BThe wireless remote control and the projector itself have the same control buttons available.
)Input select (INPUT, RGB, VIDEO) buttons
(page 24)
*ENTER button (page 28)
This button is used to accept and to activate items selected in the
+Arrow (F, G, I and H) buttons
(page 28)
These buttons are used to select and adjust items in the
,MENU button |
(pages 26 and 28) |
This button is used to display |
menu screens. When a menu |
1STD (standard) button |
|
(page 29) |
|
This button is used to reset the | Preparation |
This button is used to | |
projector adjustment values to the |
|
factory default settings.
2SHUTTER button (page 38)
momentarily turn off the picture and sound.
Storing the card remote control unit
#RGB INPUT indicator (page 17)
This indicator shows whether a signal is being input to the RGB input connectors (RGB 1 IN/RGB2 IN). When an input signal is detected, the indicator illuminates.
$LAMP indicator (page 42)
This indicator illuminates when it is time to replace the lamp unit. It flashes if a circuit abnormality is detected.
%TEMP indicator (page 42)
This indicator illuminates if an abnormally high temperature is detected inside the projector or around it. If the temperature rises above a certain level, the power supply will be turned off automatically and the indicator will illuminate or flash.
&POWER button (pages 24 and 25)
'Power indicator (pages 24 and 25)
This indicator illuminates red when the MAIN POWER switch is turned on (standby mode), and illuminates green when the power is turned on and a picture starts to be projected.
(AUTO SETUP button (pages 17 and 25)
If this button is pressed while a picture is being projected, the projection settings will be adjusted automatically in accordance with the signal being input. In addition, the angle of tilt of the projector will be automatically detected and adjusted in order to correct any keystone distortion. (“AUTO SETUP” will appear on the screen during adjustment.) Set “AUTO KEYSTN” in the OPTION1 menu to “OFF” to prevent any deterioration of the picture as a result of keystone correction.
screen is being displayed, it can |
be used to return to a previous |
screen or to clear the screen. |
-FREEZE button (page 29)
This button is used to momentarily freeze the image so that a still picture is displayed.
.VOLUME +/- buttons
These buttons are used to adjust the volume of the sound output by the projector’s
/INDEX WINDOW button (page 39)
This button can be used to split the image projection area into a still image and a moving image.
0D.ZOOM +/- buttons (page 30)
These buttons are used to enlarge certain portions of the projected image.
#Turn off the MAIN POWER switch and disconnect the power cord plug from the wall outlet. (Refer to page 25.)
$Gently turn the projector upside down.
%Open the card remote control unit holder.
&Place the card remote control unit inside.
T
AU
'Close the card remote control
unit holder.