Sound qualityUsing the preset equalizer
Press [PRESET EQ].
Each time you press the button:
XBS: Emphasizes the bass
;
CLEAR: Clarifies higher sounds
;
SOFT: For background music
;
VOCAL: Adds gloss to vocals
;
OFF:
Using the sound virtualizer
This effect stabilizes the midrange
sounds, such as vocals, and gives
sound natural width and depth.
Use it when listening to stereo
sources.
Press [S. VIRTUALIZER].
“ ” lights on the LCD.
“ ”
“ ”
“ ”
Manual tuning
Press [FM/AM, RADIO] to select the band.
Each time you press the button:
FM 1 )FM 2 )AM 1 )AM 2
^--------------------------------------------------}
Press [i, j, TUNE/CLOCK] to tune to a station.
Press and hold until the frequency starts scrolling to start automatic
tuning. Tuning stops when a station is found.
Adjust the volume.
[i]:Increase
[j]:Decrease
ª To turn the radio off
Press [POWER, Í/I].
Preset tuning
You can preset up to 20 stations: 5 each in FM 1, FM 2, AM 1, and AM 2.
ª Presetting
While listening to the station you want to preset
Press and hold a MEMO button ([1, 2, 3, 4,
or 5]) until the channel number appears.
The station occupying a channel is erased if
you preset another station in its place.
ª To listen to a preset station
1. Press [FM/AM, RADIO] to select the band.
2. Press the MEMO button ([1, 2, 3, 4, or 5]) to select the channel.
If FM reception is poor
On the remote control
Press [FM MODE].
“MONO” lights.
Sound is monaural but noise is
reduced.
Press again to cancel.
Changing the FM step
Change the FM step to receive FM stations allocated 0.1-MHz steps.
First press [FM/AM, RADIO] to select FM 1. Now, press and hold [FM/AM,
RADIO]. The display changes in a few seconds to show the current lowest
FM frequency. Continue to hold down the button.
The minimum frequency changes and the step is changed at the same
time. Changing the step erases all preset stations.
Repeat the above to change the step back.
To improve reception
4
Listening to the radio
1
2
3
VOL
+
-
SLEEP
POWER
Í
/
I
RADIO CD
FM/AM
MODE
MEMO
1
2
3
4
5
TUNE/ CLOCK
CD/RADIO
DISP/—ADJ
DISP/—ADJ
TIME SET
BUZZER
1
2
ENTER
SPEAKER
MODE
BRIGHTNESS
+-
ALARM
VOL

+

-

TUNE/CLOCK
MEMO buttons
POWER
Í/I
RADIO
FM/AM
1
2
3
FM AM
Extend and change the direction of
the antenna.
FM MODE
BRIGHTNESS
FM/AM
M1
M4 M5
FM MODE
M2 M3
CD
CD MODE
PRESET EQ
S.VIRTUALIZER
VOLUME
CD CLOCK RADIO
Changing the brightness
You can dim the clock and turn
the LCD light off.
Press [BRIGHTNESS].
Press again to brighten the clock
and turn the LCD light on.
Speaker mode
Select whether to have sound come
from both units (DUAL), the main unit
only (MAIN), or the sub unit only
(SUB).
The mode you select applies to all
sound sources and remains active
until you change it.
Press [SPEAKER MODE].
The mode changes each time
you press the button.
DUAL #MAIN #SUB
^------------------------------}
When using headphones, set the
speaker mode to DUAL. Sound will
come only from the left or right side if
you set the mode to MAIN or SUB.
Note
VOL
+
-
SLEEP
POWER
Í
/
I
RADIOCD
FM/AM
MODE
MEMO
1
2
3
4
5
TUNE/ CLOCK
CD/RADIO
DISP/–ADJ
DISP/–ADJ
TIME SET
BUZZER
1
2
ENTER
SPEAKER
MODE
BRIGHTNESS
+
-
ALARM
SPEAKER
MODE
VOL
+
-
SLEEP
POWER
Í
/
I
RADIOCD
FM/AM
MODE
MEMO
1
2
3
4
5
TUNE/ CLOCK
CD/RADIO
DISP/–ADJ
DISP/–ADJ
TIME SET
BUZZER
1
2
ENTER
SPEAKER
MODE
BRIGHTNESS
+
-
ALARM
BRIGHTNESS
PRESET EQ
FM/AM
M1
M4 M5
FM MODE
M2 M3
CD
CD MODE
PRESET EQ
S.VIRTUALIZER
VOLUME
CD CLOCK RADIO
EUR648259
S. VIRTUALIZER
FM/AM
M1
M4 M5
FM MODE
M2 M3
CD
CD MODE
PRESET EQ
S.VIRTUALIZER
VOLUME
CD CLOCK RADIO
EUR648259
^----------------------------------}
Main unit
DUAL
EQ
FM
1
FM
1
DUAL
FM
1
EQ
Channel number
“ ”