Panasonic RX-D23 Listening to radio broadcasts, Normal tuning, Preset tuning, How to preset

Indicates auto scan

3. Press [AUTO SCAN] when you find the desired station.

Auto scan ends when it reaches the original frequency again. To stop during the process, press [AUTO SCAN].

To improve reception

a station by listening to all tuned-in stations for 8

Note

Automatic tuning may stop on a frequency where there is no station if there is interference. Press [–/g] and [f/+] to tune if this occurs.

Adjust the volume.

“ ” lights when an FM stereo broadcast is being received.

Keep [–/g] or [f/+] depressed and release when the frequency display starts to change. A station with good reception is automati- cally selected and the process stops.

To stop automatic tuning, press [–/g] or [f/+] again.

2 Press [BAND] to select “FM” or “AM”.

3 (Omit this step if using the remote control)

If “ ” is on the display, press [TUNE MODE] to clear it off .

4 Press [–/g] or [f/+] to tune to the desired station.

] to “TUNER”.

The frequency changes one step each time a button is pressed.

(Power comes on.)

] to “TUNER”.

Switch [

3 2 1

To use auto scan You can search for seconds each. Preparation: Switch [

5

Automatic tuning

1

Listening to radio broadcasts

Normal tuning

5 4

1.Press [BAND] to select “FM” or “AM”.

2.Press [AUTO SCAN]. Auto scan starts.

FM: Extend the whip antenna and adjust its direction.

AM: Adjust facing of the unit.

If noise is excessive in the FM stereo mode

Press [FM MODE]. (“ ” lights up.) Sound will be produced in monaural, but this also reduces noise.

Press the button again to cancel. (“ ” goes out.)

To receive FM broadcasts allocated in 0.1 MHz

(Only from the main unit)

First press [BAND] to select “AM”. Now, press and hold [BAND]. The dis- play changes in a few seconds to show the current lowest FM frequency. Continue to hold down the button.

The minimum frequency changes and the step is changed at the same time. Changing the step erases all preset stations.

Repeat the above to change the step back.

Preset tuning

Preset the stations (12 FM and 12 AM) to make tuning simpler.

235 4

2 3 1

How to preset

1 Tune to the desired station. Do steps 1–4on the left.

2 Press [MEMORY].

3 While “” and the frequency are flashing

Press [MEMORY].

Preset channel

4 While “” and the preset channel are flashing

Press [–/g] or [f/+] to select the desired channel.

(Remote control: [4] or [3])

5 Press [MEMORY].

(This completes presetting.)

6 Repeat steps 1–5 to preset other stations.

Note

1If “ ” goes off during presetting, return to step 2.

To listen to preset channels

2Press [BAND] to select “FM” or “AM”.

(Omit this step if using the remote control)

Press [TUNE MODE] to display

3“”.

Press [–/g] or [f/+] to select the desired channel (1–12).

(Remote control: [4] or [3])

Preset channel

To use preset scan

You can search for a station by listening to all preset channels for 8 seconds each.

1. Do steps 1to 2above.

For remote control, replace [–/g] or [f/+] described below with [4] or [3].

2. Press and hold [–/g] or [f/+] until “PS” appears on the display.

Indicates preset scan

3. Press [–/g] or [f/+] when you find the desired channel.

Preset scan ends after searching through each preset channel once. To stop during the process, press [–/g] or [f/+].

3

RQT6742