Supplied accessories/AC power supply connection/Control guide/Installation
2
VQT2T88
Setup example | Front speaker | Front speaker |
| (left) | (right) |
|
| |
Connected equipment |
| |
Surround | Main unit |
|
speaker |
|
|
(left) |
|
|
Approx.120° |
| |
|
| Surround |
|
| speaker (right) |
•Aim the front face (with Panasonic logo) of each speaker at the
•Place the surround speakers slightly at the back right and left of the
Supplied accessories
Please check and identify the supplied accessories. Use numbers indicated in parentheses when asking for replacement parts.
(Product numbers correct as of January 2010. These may be subject to change.)
Only for U.S.A. and Puerto Rico: To order accessories, refer to “Accessory Purchases (United States and Puerto Rico)” on page 5.
Only for Canada: To order accessories, call the dealer from whom you have made your purchase.
2 AC power supply cords (K2CB2CB00021)
Leg cushions (1 sheet: 8 pieces)
Keep the leg cushion out of reach of children to prevent swallowing.
AC power supply connection
To save power when the system is not to be used for a long time, unplug it from the household AC outlet.
Make sure to turn this system off before unplugging the AC power supply cord.
For power consumption of speakers in Standby, see right page.
Household AC outlet | Side view |
(AC 120 V, 60 Hz) |
|
AC IN
AC power supply cord (included)
Note
The included AC power supply cords are for use with this system only. Do not use them with other equipment. Also, do not use AC power supply cord for other equipment with this system.
Control guide
Speaker (with built-in amplifier)
Pole | Side view | TEST terminal | |
| ID switch | ||
AC inlet (➜ above) | |||
| |||
|
| TEST ID | |
Base | AC IN |
| |
1 [WIRELESS LINK] indicator (➜ right | |||
(woofer | |||
part) | page) |
| |
| 2 For switching the speaker “ON/OFF” | ||
|
| (➜ right page) |
WIRELESS LINK | Note | |
TEST terminal: This is used to check the product | ||
| 1 | operation status. Only used in factory. Do not |
POWER | 2 | insert a foreign object. |
|
| ID switch: This is used to check the product |
|
| operation status and not used regularly. |
Installation
There is no positional distinction for each speaker before setting.
Make sure to place the speakers on a flat, stable surface so there is no danger of them falling over.
When carrying speakers, hold the pole and base parts. (➜ left)
The speakers of this system are not magnetically shielded. Do not install this system near a
Note
•Make sure the base parts are not covered by cloth such as a curtain.
•Before attaching the leg cushion (included) on the base parts to prevent tilt or rattle on the floor, make sure there are no people in the surrounding area.
•Set the distance from each speaker to the
Wireless functions
As this system uses a frequency band of 2.4 GHz, the radio waves may be interrupted by an obstacle. Depending on the surrounding environment (i.e. radio wave interruption from outside, etc.) or the building structure where this system is used (i.e. wall that easily reflects radio waves, etc.), sounds may be cut or noise may occur. Install this system properly paying attention to the following descriptions.
Equipment certification
As this system received Technical Conditions compliance certification based on the Radio Law, the wireless station license is not required. However, if you do the following actions to this system, you may be
held accountable by law.
•Disassemble or refurbish Restrictions for use
•Domestic use only.
•Use this system in the same room.
Do not place an obstacle between the main unit
Radio waves from this system reach a maximum range of 15 m
(49 feet) in the same room. If there is an obstacle between the main unit
Keep this system away from equipment that generates radio wave interference.
If the following equipment is located near the system, install this system away from such equipment.
•Bluetooth, OA devices, telephone, etc.: approx. 3 m (10 feet) or more
•Microwave oven, wireless LAN compatible devices: approx. 3 m (10 feet) or more
This system is designed to automatically avoid radio wave interference with such household equipment. If radio wave interference occurs, the Wireless Link display (➜ page 14 of
Keep this system away from metal objects that tend to reflect radio waves.
If there are metal objects or furniture in the room where this system is installed, radio waves tend to be reflected. Depending on the listening- viewing position, sounds may be interrupted or noise may occur. These symptoms may be remedied by slightly moving this system’s position.
Note that radio waves tend to be reflected also when this system is installed in rooms with a lot of activity.
