14
RQT9743
[SC-HC38DB]
DAB/DAB+ reception is poor.
≥Keep the antenna away from computers, televisions, other cables
and cords.
≥Use an outdoor antenna (l5).
A beat sound or noise is heard while receiving
radio broadcast.
≥Adjust the position of the antenna.
≥Try to keep a certain amount of distance between the antenna and
AC mains lead.
≥Try using an outdoor antenna if there are buildings or mountains
nearby.
≥Switch the television or other audio players off or separate it from
this unit.
≥Keep this unit away from mobile phones if the interference is
apparent.
[SC-HC38] ([Australia[and[New[Zealand[ only)
Stations cannot be selected.
Change the AM frequency step.
1Press [RADIO] to select “AM”.
2Press and hold [SELECTOR] on the unit.
After a few seconds the display changes to show the current lowest
frequency. Continue to hold the button down. The lowest frequency
changes and the step is changed.
[SC-HC38] ([Australia[and[New[Zealand[ only)
A low hum or noise is heard during AM broadcast.
≥Keep the AM antenna away from this unit, other cables and cords.
Cannot charge or operate.
≥Have you selected the appropriate selector?
Press [iPod] to select either “IPOD_DOCK” or “IPOD_PORT”.
≥Check that the iPod/iPhone/iPad is connected properly. (l6)
≥The battery of the iPod/iPhone/iPad is depleted. Charge the iPod/
iPhone/iPad, and then operate again.
≥Connect the iPod/iPhone/iPad again or try to restart the iPod/
iPhone/iPad.
≥When this unit is in standby mode, charging will not start when
using the “IPOD_PORT” connection.
Turn this unit on and make sure the charging has started before
switching this unit to standby mode.
Pairing cannot be done.
≥Check the Bluetooth® device condition.
The device cannot be connected.
≥The pairing of the device was unsuccessful or the registration has
been replaced. Try pairing the device again. (l7)
≥This unit might be connected to a different device. Disconnect the
other device and try pairing the device again. (l7)
The device is connected but audio cannot be heard
through this unit.
≥For some built-in Bluetooth® devices, you have to set the audio
output to “SC-HC38” manually. Read the operating instructions for
the device for details.
The sound is interrupted.
≥The device is out of the 10 m communication range. Bring the
Bluetooth® device closer to this unit.
≥Remove any obstacle between this unit and the device.
≥Other devices that use the 2.4 GHz frequency band (wireless
router, microwaves, cordless phones, etc.) are interfering. Bring
the Bluetooth® device closer to this unit and distance it from the
other devices.
≥Select “MODE 1” for stable communication. (l7)
The remote control doesn’t work properly.
≥The remote control and this unit are using a different code.
(l15, “REMOTE ”)
≥Is the battery depleted or is the battery inserted incorrectly? (l4)
The following messages or service numbers may
appear on the unit’s display.
“--:--”
≥You plugged the AC mains lead in for the first time or there was a
power failure recently. Set the time (l12).
“ADJUST CLOCK”
≥Clock is not set. Adjust the clock accordingly.
“ADJUST TIMER”
≥Play timer is not set. Adjust the play timer accordingly.
“AUTO OFF”
≥The unit has been left unused for about 30 minutes and will shut
down within a minute. Press any button to cancel it.
“CANNOT SET”
≥Select an audio source other than “BLUETOOTH”.
“CHECKING CONNECTION”
≥The unit is checking the connected iPod/iPhone/iPad.
≥If this display keeps appearing, make sure that the battery of the
iPod/iPhone/iPad is not depleted and that the iPod/iPhone/iPad is
turned on and connected correctly (l6).
“ERROR”
≥Incorrect operation is performed. Read the instructions and try
again.
“F” (“ ” stands for a number.)
≥There is a problem with this unit.
Note down the displayed number, disconnect the AC mains lead
and consult your dealer.
Radio
≥Confirm the antenna(s) are properly connected. (l5)
iPod/iPhone/iPad operations
Bluetooth®
Remote control
Messages
SC-HC38_DBEB_DBGN_GS~RQT9743-B.book 14 ページ ２０１３年１月２１日 月曜日 午後１時６分