15
RQT9743
“ILLEGAL OPEN”
≥Sliding door is not in correct position. Turn the unit off and on
again. If this display appears again, consult the dealer.
“IPOD_DOCK OVER CURRENT ERROR”
“IPOD_PORT OVER CURRENT ERROR”
≥The iPod/iPhone/iPad is drawing too much power. Disconnect the
iPod/iPhone/iPad and turn the unit off and on again.
≥The USB device is drawing too much power. Switch to “CD”
mode, remove the USB and turn the unit off.
“NODEVICE”
≥The iPod/iPhone/iPad device is not inserted correctly. Read the
instructions and try again (l6).
≥The battery of the iPod/iPhone/iPad is depleted. Charge the iPod/
iPhone/iPad and turn it on before connecting.
≥The USB device is not inserted. Check the connection.
“NO DISC”
≥Insert the disc to be played (l6).
[SC-HC38DB]
“NO MEMORY”
≥There are no preset DAB/DAB+ stations to select. Preset some
channels. (l9)
“NO PLAY”
≥A CD that is not in CD-DA or MP3 format is inserted. It cannot be
played.
≥If there are more than 255 albums or folders (audio and
non-audio), some of the MP3 files in these albums may not be
read and played. Transfer these music albums to another USB.
Alternatively, reformat the USB device and save these music
albums prior to saving the other non-audio folders.
[SC-HC38DB]
“NO SIGNAL”
≥This station cannot be received. Check your antenna (l5).
“NOT SUPPORTED”
≥You have connected an iPod/iPhone/iPad that cannot be played
(l16).
≥If the iPod/iPhone/iPad is compatible, turn it on and connect it
correctly.
“READING”
≥The unit is checking the CD information. After this display has
disappeared, start operating.
“REMOTE ” (“ ” stands for a number.)
≥The remote control and this unit are using different codes. Change
the code on the remote control.
– When “REMOTE 1” is displayed, press and hold [OK] and [ ]
for more than 4 seconds.
– When “REMOTE 2” is displayed, press and hold [OK] and [CD/
RADIO] for more than 4 seconds.
[SC-HC38DB]
“SCAN FAILED”
≥Stations are not receivable. Check your antenna and try Auto
scanning (l9).
If “SCAN FAILED” is still displayed find the best signal reception
with the “MANUAL SCAN” tuning function. (l10)
About Bluetooth®
∫Frequency band used
≥This unit uses the 2.4 GHz frequency band.
∫Certification of this device
≥This system conforms to frequency restrictions and
has received certification based on frequency laws.
Thus, a wireless permit is not necessary.
≥The actions below are punishable by law in some
countries:
– Taking apart or modifying the unit.
– Removing specification indications.
∫Restrictions of use
≥Wireless transmission and/or usage with all
Bluetooth® equipped devices is not guaranteed.
≥All devices must conform to standards set by
Bluetooth SIG, Inc.
≥Depending on the specifications and settings of a
device, it can fail to connect or some operations can
be different.
≥This system supports Bluetooth® security features.
But depending on the operating environment and/or
settings, this security is possibly not sufficient.
Transmit data wirelessly to this system with caution.
≥This system cannot transmit data to a Bluetooth®
device.
∫Range of use
≥Use this device at a maximum range of 10 m. The
range can decrease depending on the environment,
obstacles or interference.
∫Interference from other devices
≥This unit may not function properly and troubles such
as noise and sound jumps may arise due to radio
wave interference if this unit is located too close to
other Bluetooth® devices or the devices that use the
2.4 GHz band.
≥This unit may not function properly if radio waves
from a nearby broadcasting station, etc. is too
strong.
∫Intended usage
≥This unit is for normal, general use only.
≥Do not use this system near an equipment or in an
environment that is sensitive to radio frequency
interference (example: airports, hospitals,
laboratories, etc).
Panasonic bears no responsibility for data and/
or information that is compromised during a
wireless transmission.
SC-HC38_DBEB_DBGN_GS~RQT9743-B.book 15 ページ ２０１３年１月２１日 月曜日 午後１時６分