Panasonic SC-HT95 Speaker cords, About 10 cm, Attaching to a wall, Attaching to speaker stands

Speaker cords

Attach the stickers to the speaker cords.

≥Attach the numbered stickers to the end of the speaker cords so the numbers match the positions of the speak-

ers shown in the diagram.							About
							10 cm
								(4")
6	5	4	3	2	1	1
6	5	4	3	2	1
						L FRONT
						FRONT L		FRONT L
6	5	4	3	2	1
6	5	4	3	2	1	1		1

Twist the vinyl tip and pull off.

1 3

2

setup

≥Connect the cords to the terminals of same color so the num- bers on the stickers match the numbers under the terminals.

≥Never short-circuit positive (i) and negative (j) speaker wires. ≥Be sure to connect only positive (red or gray) wires to positive (i) terminals and negative (black or gray with blue stripe) wires

to negative (j) terminals.

Incorrect connection can damage the speakers.

≥After you have completed setup and connection, wind the ex- Black cess cord and keep together with string.

≥The speaker nets cannot be removed.

Notes on speaker use

≥You can damage your speakers and shorten their useful life if you play sound at high levels over extended periods.

Reduce the volume in the following cases to avoid damage.
–When playing distorted sound.	+ Red

Red Gray

6	5	4	3	2	1
		R
			L	R
	CENTER				L
	SUBWOOFER		SURROUND		FRONT

SURROUND R

+ Gray (no stripe)

- Gray with blue stripe

Blue

			FRONT L
	FRONT	R	1	Front speaker (left)
SURROUND L	2		Front speaker (right)
3	Surround speaker (left)

Simple

–When the speakers are receiving howling from a micro-	- Black
phone or record player, noise from FM broadcasts, or con-
tinuous signals from an oscillator, test disc, or electronic
instrument.
–When adjusting the sound quality.
–When turning the unit on or off.

	CENTER	4	Surround speaker (right)
SUBWOOFER	5	Center speaker
6	Subwoofer

Attaching to a wall

Front and surround speakers can be attached to a wall.

Attach four speaker feet to each speaker, ensuring they do not cover the holes.

Set the speaker onto screws and slide through bracket to lock into position.

]HT95]

Speaker feet (included)

Screw (not included)	30–35 mm
	(13⁄16q–13⁄8q)
	Ø7.5–9.5 mm
	(19⁄64q–3⁄8q)
	7–9 mm
	(9⁄32q–23⁄64q)
106 mm (411⁄64q)

Attaching to speaker stands

Ensure the following conditions are met when you purchase your speaker stands.

≥Observe the diameter and length of the screws and the distance between screws as shown in the diagram.

≥The stands must be able to support over 10 kg (22 Ib.) for SB-AFC286 and 5 kg (11 Ib.) for SB-AFC95.

≥The stands must be stable even if the speakers are in a high position.

5 mm (13⁄64q),
pitch 0.8 mm	60 mm (223⁄64q)
(1⁄32q)

Attach the stands

Speaker feet	Screw (not included)
(included)

[HT75]

The method for attaching speakers to a wall is the same except that there is only one bracket.

Note

The wall or pillar on which the speakers are to be attached should be capable of supporting 10 kg (22 Ib.) for SB-AFC286 and 5 kg (11 Ib.) for SB-AFC95 per screw.

with these holes.

Plate thickness

plus 7 to 10 mm (plus 9⁄32q to 25⁄64q)

Speaker stand (not included)

7

RQT6183