Panasonic SC-HTB8 Advanced operations, Auto Power Down, Dimmer mode, Bluetooth Stand-by

Advanced operations

Auto Power Down Dimmer mode

The main unit is automatically turned off if there is no audio input and when you do not use it for approx. 2 hours.

While pressing and holding [CLEAR VOICE] on the remote control, press and hold [INPUT] on the main unit for more than 4 sec to display the current setting.

ャュバュヷュ “BD/DVD” indicator blinks:

Auto Power Down is on.

ヤロユモンチヷヰリヤユ “CLEAR VOICE” indicator blinks:

Auto Power Down is off.

While the setting is displayed, press [CLEAR VOICE] to select the setting.

≥The setting changes each time [CLEAR VOICE] is pressed.

≥The indicator for the selected setting blinks for 20 sec and then exits the setting mode.

≥The setting is maintained until it is changed again.

≥Default setting of this function is off.

Bluetooth® Stand-by

This function allows you to connect a paired Bluetooth® device when the main unit is in standby mode.

While pressing and holding [SURROUND] on the remote control, press and hold [ ] on the main unit for more than 4 sec to display the current mode.

ャュバュヷュ “BD/DVD” indicator blinks:

Bluetooth® Stand-by is on.

ヤロユモンチヷヰリヤユ “CLEAR VOICE” indicator blinks:

Bluetooth® Stand-by is off.

You can turn off dimmer mode and keep the LED indicators bright.

While pressing and holding [INPUT] on the remote control, press and hold [s VOL] on the main unit for more than 4 sec to turn off Dimmer mode.

≥The indicator for the current condition will turn brighter.

≥The setting is maintained until it is changed again.

≥Default setting of this function is on.

To turn on dimmer mode, repeat the operation above. After performing the operation, the indicator for the current condition will be dim.

Others

∫Remote control code

When other Panasonic devices respond to this system’s remote control, change the remote control code on this system and the remote control.

Preparation

≥Turn off all other Panasonic products.

≥Turn on the main unit.

Change the remote control code to code 2:

1Aim the remote control at the main unit’s remote control sensor.

2Press and hold [MUTE] and [ ] on the remote control for more than 4 sec.

≥All the indicators will blink for 10 sec when the code of this system is changed.

ヵヷ ャュバュヷュ ヤロユモンチヷヰリヤユ ヴヶンンヰヶワュ

≥The setting is maintained until it is changed again.

≥If the main unit does not operate after changing the code, repeat steps 1 and 2.

≥To change the remote control code to code 1, repeat the steps above, but replace [ ] with [INPUT].

While the mode is displayed, press [SURROUND] to select the mode.

≥The setting changes each time [SURROUND] is pressed.

≥The indicator for the selected setting blinks for 20 sec and then exits the setting mode.

≥The setting is maintained until it is changed again.

≥Default setting of this function is off.

16 VQT5J41

∫To turn off the volume limitation

If a state of the lowered volume disturbs you every time the main unit turns on, for example, it is possible to turn off this function as follows:

While pressing and holding [MUTE] on the remote control, press and hold [VOL i] on the main unit for more than 4 sec.

≥All the indicators will blink once when the volume limitation is turned off.

ヵヷ ャュバュヷュ ヤロユモンチヷヰリヤユ ヴヶンンヰヶワュ

To reset the setting, return to the factory preset. (> p. 17)