Panasonic SC-ZT2 warranty Digital signals that can be played on this system, Maintenance

		Problem		Possible solution	Pages
			•	Confirm “VIERA Link “HDAVI Control” setting” is set to “ON ” (when the	23
				operation is linked).
				When it is “OFF ”, change to “ON ”.
			•	VIERA Link “HDAVI Control” does not function in Standby condition (HDMI off mode)	22
				when this system is turned off. See “Reducing Standby power consumption (In Standby
				condition (HDMI off mode))” and set to “ON ” (normal power consumption).
	VIERA Link		•	Check VIERA Link “HDAVI Control” settings of the connected equipment.	—
			•	VIERA Link “HDAVI Control” may not function when you change the	—
	“HDAVI Control” does			connections for HDMI equipment, insert and remove the outlet, or during
	not function properly.			blackout. Do the following operations in this case:
				– Turn on the TV (VIERA) again while all the equipment connected with HDMI
				cables is on.
HDMI				– Set “VIERA Link “HDAVI Control” (HDMI equipment control)” of the TV (VIERA) to “OFF” and
				then set to “ON” again. (For details, refer to the operating instructions for the TV (VIERA).)
				– Connect this system to the TV (VIERA) using the HDMI cable, switch the TV
				(VIERA) on, unplug this system’s AC power supply cord, and insert it into a
				household AC outlet again.
	Even if multi-channel audio
	sources, such as DVD, Blu-ray		•	When using VIERA Link “HDAVI Control” and the speaker is set to “TV”, press	18
	disc, are played back,			the VIERA Link button on the remote control of the TV (VIERA) and set the
	“	DIGITAL” or “DTS” is not		speaker to “Home Cinema”.
	displayed.
	This system’s input automatically
	switches to “AUX2 / STB ”, but		•	After “Setting for automatically switching the input source to STB”, the	10
	sound is not heard.
				connection might have been changed. Select OFF once and SET again.
	Or unexpected sound from other
	equipment is heard.
	[WIRELESS LINK]		•	When the [WIRELESS LINK] indicator is off, check the connection of the AC	12,13,15
				power supply cord of the speakers and check that each speaker is “ON”.
	indicator on the speakers		•	If the [WIRELESS LINK] indicator does not change from red to green, the main unit and speakers	13,15
	does not light green.			are not linked. Make sure that the main unit is “ON”. Or make the speaker settings again.	—
	Sounds are interrupted.		•	You may be using wireless headphones or the wireless LAN may be operating near this
Speakers				system. These symptoms may be remedied by slightly moving this system’s position.
	and green alternately.)		•	Straining of the speakers through excessive volume or power.	—
	Sound stops.				—
	(The indicator blinks red		•	Amplifier output is abnormal.	—
	The protection circuit		•	This may occur if you use the system in an extremely hot environment.
	is activated when some			D Determine and correct the cause, then turn the system on.
	abnormality is detected,			(The protection circuit is reset.)
	and turns off the system			(Consult your dealer if the problem persists.)
	automatically.

Digital signals that can be played on this system

guide/Digital signals that can be played on this system/Maintenance

„Dolby Digital Blu-ray disc, DVD etc.

„DTS

Blu-ray disc, DVD etc.

„PCM (2-channel) CD, DVD audio etc.

„Multi-channel LPCM (Linear PCM) Blu-ray disc, DVD audio etc.

„This system supports 3D, X.V. Color or Deep Color.

Note

•With HDMI connection, this system can play back multi-channel LPCM signals with sampling frequencies of over 48 kHz and PCM signals of over 96 kHz in addition to multi-channel LPCM of up to 48 kHz and PCM of up to 96 kHz. (If frequency exceeds these figures, playback equipment performs down-sampling and plays back as 48 kHz signals. However, playback may be impossible depending on the discs. See operating instructions of playback equipment for more information.)

•With the optical fiber connection, this system can play multi-channel LPCM signals with sampling frequencies of up to 48 kHz and PCM signals of up to 96 kHz.

•See “Glossary” (➜ page 28) for more detailed information on each signal.

informationand Troubleshooting

Maintenance

Unplug the AC power supply cord from the household AC outlet and wipe the system using a soft and dry cloth.

•When the system is very dirty, wring the cloth soaked in water thoroughly, wipe the dirt and wipe moisture off with a dry cloth.

•Do not use solvents such as benzine, thinner, alcohol, etc. because they may cause casing to deform and coating to come off.

•Before using chemically treated cloth, read the instructions that come with the cloth carefully.

Troubleshooting other

27

VQT2R70