wVehicle Detector Normal/Override On/Off Switches
(VEHICLE DETECTOR, NORMAL/OVERRIDE ON/OFF)
NORMAL: The vehicle detector turns on only when a vehicle is detected at the menu board. When the detector is turned on, a beep tone is heard in the headset. After the beep tone, the menuboard speaker turns on to allow the communication with the customer. When the vehicle leaves, the vehicle detector turns off.
OVERRIDE ON: The vehicle detector is always turned on.
OFF: Vehicles are not detected at the menuboard. No beep tone is heard in the headset, and the menuboard speaker remains off.
eChannel Group Selection Switch (CH SELECT, 1 to 8)
This switch selects the group from 8 positions.
Note: Do not set this switch to positions other than 1 to
8.That will result in an error, and TRANSCEIVER MONITOR Indicator will blink in red.
rCircuit Protector button (CIRCUIT PROTECTOR)
If excessive current flows to the center module, the cir- cuit protector is triggered. When this button is sticking out, turn off the POWER switch, press this CIRCUIT PROTECTOR button, and turn on the POWER switch again.
If the circuit protector is soon triggered again, consult your dealer or authorized service center for assistance.
tPower On/Off Switch (POWER, ON/OFF)
This switch turns the power of the center module on and off.
Channel Monitor
Channel Monitor is the mode to check if other devices have already used the desired channel at the time of the installation. The following is how to activate Channel Monitor.
When you set the POWER switch to ON while holding down the O/T TALK LOCK RELEASE switch, Channel Monitor is activated. To return to the default mode, turn off and on the power again with the POWER switch.
yTalk/Page Indicator (TRANSCEIVER MONITOR, Red/ Green/Amber)
Red:
•When the order taker unit is in the Talk Communication, the indicator lights up in red.
•When an error happens, the indicator always blinks in red.
Green:
When the order taker unit is in the Page Communication, the indicator lights up in green.
Amber:
When the gooseneck microphone is enabled, the indicator lights up in amber.
uPower Indicator (POWER) (Green)
This indicates that the power of center module is on.
iVehicle Detector Indicator (VEHICLE PRESENT) (Amber)
This indicates that a vehicle has been detected.
oMenuboard Speaker Volume Control (MENU SP, 0 to 10)
This control sets the output level of Menuboard Speaker to the optimum level for speaking to the cus- tomer.
Notes:
•Adjust this control after you set the VEHICLE DETECTOR switch to OVERRIDE ON and the vehi- cle detector indicator lights up. Otherwise, you cannot adjust the volume level.
•The line marked on this control is a standard posi- tion for this adjustment. Adjust this control to the suitable position so that feedback does not occur.
!0Remote Speaker Volume Control (REMOTE SP, 0 to 10)
This control sets the output level of Remote Speaker to the optimum level.
Notes:
•Adjust this control after you set the VEHICLE DETECTOR switch to OVERRIDE ON and the vehi- cle detector indicator lights up. Otherwise, you cannot adjust the volume level.
•The line marked on this control is a standard posi- tion for this adjustment.
Adjust this control to the suitable position so that feedback does not occur.
!1Menuboard Microphone Volume Control (MENU MIC, 0 to 10)
This control sets the input level of Menuboard Microphone to the optimum level.
Notes:
•Adjust this control after setting the VEHICLE DETECTOR switch to OVERRIDE ON and the vehi- cle detector indicator lights up. Otherwise, you cannot adjust the volume level.
•The line marked on this control is a standard posi- tion for this adjustment. Adjust this control to the suitable position so that feedback does not occur.
!2Auxiliary Input Level Control (AUX IN, 0 to 10)
This controls the input level of the AUX INPUT termi- nals.
!3Vehicle Detector Beep Volume Control (BEEP, 0 to 10)
This control sets the
10
