Panasonic WX-CC2010 operating instructions 4Day/Night Selection Switch DAY/NIGHT

!4Day/Night Selection Switch (DAY/NIGHT)

In the Day mode, you will not hear the beep tone of the other lane in the headset that sounds when the vehicle detector is on and that sounds when you press the but- ton T of the order taker unit.

In the Night mode, you will hear the beep tone of either lane in the headset when the vehicle detector of either lane is on. Once you press the button T, you will no longer hear your lane’s beep tone. However, you will continue to hear the other side’s beep tone when the other side vehicle detector is on, until the button T of the other side’s order taker unit is pressed.

Note: The following is the beep patterns.

Beep A: Pi...Pi...

Beep B: PiPi...PiPi...

Beep C: Pi..PiPi...Pi..PiPi...

State of lane	Order	Day mode	Night mode
	taker unit
Vehicle detec-	A	Beep A	Beep A
tor at Lane A is
ON.	B	Beep A	Beep A
Vehicle detec-	A	Beep B	Beep B
tor at Lane B is
ON.	B	Beep B	Beep B
Vehicle detec-	A	Beep C	Beep C
tors of both		(When you press	(When you
lanes are ON.		the button T, the	press the
		beep tone will be	button T,
		deactivated.)	Beep C will
			change to
			Beep B.
	B	Beep C	Beep C
		(When you press	(When you
		the button T, the	press the
		beep tone will be	button T,
		deactivated.)	Beep C will
			change to
			Beep A.

!5Order Taker Unit Talk Lock Release Switch

(O/T TALK LOCK RELEASE)

This switch is used to release temporarily the talk lock mode of the order taker unit.

!6Menuboard Microphone Terminals (MENU BOARD MIC: H, C, GND)

These terminals are used for the connection with Menuboard Microphone (Speaker Microphone WX- C550).

The audio level is –61 dBV, 8 Ω, balanced.

!7Menuboard Speaker Terminals (MENU BOARD SP 8 Ω: H, C, GND)

These terminals are used for the connection with Menuboard Speaker (Speaker Microphone WX-C550). The audio level is 8 Ω, 3 W, unbalanced.

!8Remote Speaker Terminals (REMOTE SPEAKER: H, GND)

These terminals are used for the connection with Remote Speaker.

The audio level is 8 Ω, 3 W, unbalanced.

Note: The remote speaker is a locally procured acces- sory.

!9Double Drive Through Control Output Terminals (DDT CONTROL: OUT, GND)

To compose Double Drive Through of two center mod- ules, these terminals are used for the connection with the DDT (IN, COM) terminals of the other center mod- ule.

•The DDT CONTROL OUT terminal is connected with the DDT IN terminal of the other center mod- ule.

•The DDT CONTROL GND terminal is connected with the DDT COM terminal of the other center module.

@0Auxiliary Input Terminals (AUX INPUT: H, C, GND)

These terminals are used for the connection with the line or the connection with a gooseneck microphone. Note: When connecting the gooseneck microphone,

set the AUX IN SEL switch to G/MIC.

@1Gooseneck Microphone PTT Terminals (G/MIC PTT: IN, COM)

These terminals are used for the connection with the PTT cable of a gooseneck microphone (locally pro- cured).

@2Vehicle Detector Terminals (V/DET: IN, COM)

These terminals are used for the connection with the output terminal of vehicle detector.

@3Double Drive Through Control Input Terminals (DDT: IN, COM)

To compose Double Drive Through of two center mod- ules, these terminals are used for the connection with the DDT CONTROL (OUT, GND) terminals of the other center module.

•The DDT IN terminal is connected with the DDT CONTROL OUT terminal of the other center mod- ule.

•The DDT COM terminal is connected with the DDT CONTROL GND terminal of the other center mod- ule.

@4Transformer Terminals (TRANSFORMER 12V AC: GND, LOAD)

These terminals are used for the connection with WX- C516 Power Transformer.

11