ParaBody 704101 manual Reggie Whiteall PRO SYSTEMASSEMBLYINSTRUCTIC~NS, IN. Locknuts

704101 REGGIE WHITEALL PRO SYSTEMASSEMBLYINSTRUCTIC~NS

Insert three (3) I-_: -: IN. SQ. ENDCAPSinto the ends of the BEARINGHOUSINGas shown drawing.

Slide the BEARINGHOUSINGdown over the FRONTUPRIGHTof the UPRIGHTFRAMEto the first set of holes ~ sb, ownon drawing. SECURELYassemble it to the UPRIGHTusing two (2) 3/8 X

3/4 IN. BOLTS,a.-.d ~vo (2) 3/8 IN. LOCKNUTS.

LOOSELYasser=.z:.e three (3) 3-1/2 IN. PULLEYSand. six i5) 3/8 IN. SPACERSin between the two PULLEYMOUNTFLATSas shown on drawing,, ";' 2 three (3) 3/8 X 2-.~/4 IN. BOLTS.and three (3)

3/8 IN. LOCKNU'TS.

10.LOOSELYasse.-..~:,e the PULLEYMOUNTFLAT ASSE~IBLYto the UPRIGHTFRAMFas shown on drawing, using v,~o (2) 3/8 X2-3/4 IN. BOLTS,and two (2) 3/8 IN. LOCKNUTS.

11.LOOSELYassembIe the HORIZONTALSUPPORTin bev,~een the PULLEYMOUNTFt,ATS as shownon drawin2-, asing one (1) 3/8 X 2-3/4 IN. BOLT,and one (1) 3/8 IN. LOCK

12.Attach thirty-two ~,32) PARAGLIDESTRIPSto the :,so (2) BARHOLDERSand the two (2) SAFETY RAILSas shown:,r. (DETAILA) using the following steps:

S

A. Thorou~.'.i': clean all inside surfaces where:ine PAR-~,GLIDEare to be attached.

B.

Remove2~e PARAGLIDESfrom paper backing the and firmly apply them to all shownsurfaces

~

(8 places

13.SECURELYAssemble four (4) SPRINGPIN ASSEMBLIESto the SPRINGPIN BARRELS,of the two

(2)BARHOLDERSand the two (2) SAFETYRAILSas shown in (DETAILB). (!!! I;MPORTANT TIGHTEN THE NUT OF THE SPRING PIN ASSEMBLYSECURELY)

14.Pull back the SP~.NGPIN on the SAFETYRAILSand slide one downover each UPRIGHTas shown on drawing. Eng=gethe SPRINGPIN into a desired ~djustment hole.

15.Pull back the SP,~NGPIN on the BARHOLDERSand slide one down over each UPRIGHTas shown on drawing. Engzge the SPRINGPIN into a desired adjustment hole.

16.

LOOSELYasse:..,z[e the two (2) UPRIGHTASSEMBLIES.:o the BASEas shown on drawing, using four

(4)3/8 X 2-3/4 IN. BOLTS,and four (4) 3/8 IN. LOCKNUTS.

17.LOOSELYasse.-.,b!e the two UPRIGHTSto the ends of the HORIZONTALSUPPORTa~; shown on drawing, using v.~ z (2) 3/8 X 2-3/4 IN. BOLTS,fou: (4) 3/8 IN. WASHERS,and two (2) 3i8 IN.

NUTS.

18.AT THIS TIME TIGHTEN ALL LOOSE FRAME CONNECTIONS MADETO THIS POINT.

19.Insert four (4) 2 ~. SQ. ENDCAPSinto BOTHENDSof the LEFT, and RIGHTPEC DECARMS shown on drawing.

20.Insert four (4) 1 2 ~. FLANGEBEARINGSinto the BUSHINGSof the BEARINGHOUSING, shown on drawing.

5

11/21/95