ParaBody 704101 manual Reggie White ALL PRO System Assembly INSTRUCT, IONS~

704101 REGGIE WHITE ALL PRO SYSTEM ASSEMBLY INSTRUCT, IONS~

Insert the LEFT and RIGHTPEC DECARMSthrough the 1/2 IN. FLANGEBEARINGSin the

21.BEARINGHOUSINGon their respective sides as shown on drawing, and SECUREthem in place with two (2) ~ 2 IN. ID. PRESS-ONCAPS.

22.Slide tx~o (2) 4 X 12 ROLLERPADSonto :he LEFT and RIGHTPEC DECARMSuntil the ROLLER PAD is ,:LUSH with the bottom of the ARMS.(IF A LUBRICANTIS REQUIRED,COATTHE

INSIDE OF THE ROLLER PAD WITH RUBBING ALCOHOL. ALSO, ROTATING THE PAD WHlLE PUSHING UP WILL HELP TO EASE ASSEMBLY)

23.Attach ~wo (2) CARRIAGEGUIDESto the CAMSTOP on the BEARINGHOUSINGwhere the CAMS of the PEC DECARMScontact the CAMSTOP.

24.LOOSELYassemble two (2) 3-1/2 IN. PULLEYS,and two (2) CABLERETAININGCLIPS to PLATESof the BEARINGHOUSINGas shown on drawing, using two (2) 3/8 X 2 IN. BOLTS,P, vo (2)

3/8 IN. WASHERS,and two (2) 3/8 IN. LOCKNUTS. (NOTE: THIS CONNECTIONWILL TIGHTENED AFTER THE CABLE HAS BEEN ROUTED)

SECURELYassemble the SMALLBACKPAD to the UPRIGHTFRAMEas shown on drawing, using

25.

two (2) 3/8 X 2-I/2 IN. BOLTS,and two (2) 3/8 IN. LOCKWASHERS.

26.SECURELYassemble one (I) 3-1/2 IN. PULLEY,and two (2) 3/8 IN. SPACERSin betwee:~

PLATESat the bottom of the UPRIGHTFRAMEas shown on drawing, using one (I) 2-3/4 IN. BOLT, and one ~1) 3/8 IN. LOCKNUT.

27.LOOSELYassemble two (2) 3-1/2 IN. PULLEYS,and two (2) CABLERETAININGCLII?S to PLATESof the UPRIGHTFIL,~MEas shown on drawing, using two (2) 3/8 X 2 IN. BOLTS,two (2)

IN. WASHERS,and two (2) 3/8 IN. LOCKNUTS. (NOTE: THIS CONNECTIONWILL TIGHTENED AFTER THE CABLE HAS BEEN ROUTED)

28.

LOOSELYassemble p, vo (2) CONNECTORPLATESaround two (2) 3-1/2 IN. PULLEYS;.using t~,vo

(2)3/8 X 2 IN. BOLTS, and two (2) 3/8 IN. LOCKNUTS. (NOTE: THIS CONNECTIOt~'WILL

TIGHTENED AFTERTHE CABLE HAS BEEN ROUTED)

NOTE: BEFORE PROCEEDING WITH CABLE INSTALLATION, UNRAVEL CABLES, AND REMOVE AS MUCHSPIRALING AS POSSIBLE.

To ins:zll LOOPCABLE,start by inserting the BALLENDSof the CABLEinto the BUSHINGSon the

29.

CAMSofthe LEFT and RIGHT PEC DEC ARMS.

Drape ~oth sides of the CABLEo(,er the PULLEYSon the BEARINGHOUSINGPosition. CABLE RETAININGCLIPSin a vertical positior, over the PULLEYand CABLE,after the LOOPCABLEhas

been routed. Tighten the PULLEYCONNECTIONcompletely.

¯Place one (1) 3-I/2 IN PULLEYinto the LOOPof the CABLEcreated from the above stel:,, and SECURELYassemble the PULLEYBRACKETto the PULLEY,using one (1) 3/8 X 1-3,4 IN. BOLT,

and one (1) 3/8 IN. LOCKNUT. (NOTE: MAKESURE THATTHE CABLEIS IN TE[E GROOVE OF THE PULLEY BEFORE TIGHTENING)

¯See CABLEROUTINGDIAGRAMfor help in completing this step.

6

1 I,°-1/95