ParaBody 704101 manual Reggie White All Pro System Assembly Instructions

704101 REGGIE WHITE ALL PRO SYSTEM ASSEMBLY INSTRUCTI[ONS

To install the HIGHPULLEYCABLE.start by routing the end of the CABLEWITHOUTthe WHITE

30.

BALLover the TOP PULLEYon the PULLEYMOUNTFLATS. After the CABLEhaz been:~eholeroutedin front SECURELYassemble one (1) 3/8 X ,.-~4 IN. BOLT,and one (I) 3/8 IN. LOCKNUT

of the PULLEYon the PULLEY MOUNTFLATS. (DO NOT OVERTIGHTEN THIS BOLT)

Run CABLEover and down the SECONDPULLEYof the PULLEYMOUNTFLATS. Run the CABLEaround one of the PULLEYSof the PULLEYBLOCKand up to the THIRDPULLEYof the

PULLEY MOUNT FLATS.

Pall CABLEover and down the THIRDPULLEY.to the CARRIAGEand a::ach the CABLEto the CARRIAGE,using one (1) QUICKLINK. (SEE DETAIL

See CABLEROUTINGDIAGRAMfor help in completing this step.

To install LOWPULLEYCABLE,start by inserting the end of the CABLE~,~,ITHOUTthe WHITE

BALLunder the FRONTPULLEYof the UPRIGHTFRAME.After the CABLEhas ~en routed SECURELYassemble one (1) 3/8 X 2-3/4 IN. BOLT,and one (I) 3/8 lN. LOCKNUTto :he hole

underneath the FRONTPULLEY. (DO NOT OVERTIGHTEN THIS BOLT)

Run the CABLEback to and around the second PULLEYbehind the FRONTPULLEY-After the CABLEhas been routed, position the CABLERETAININGCLIPin a vertical positior~ :ader the

PULLEYand CABLEand tighten the PULLEYCONNECTIONcompletel).

Run the CABLEup to and around the BOTTOMPULLEYon the PULLEYBLOCK.(NOTE: THE

CABLE MUST BE ROUTED AROUND THE BOTTOM PULLEY FROM THE REAR "FO THE FRONT)

Run the CABLEdown to and around the PULLEYbehind the SMALLSEATPADon ,2~e UPRIGHT FRAMEand attach the end of the CABLEto the PULLEYBRACKETof the LOOPCABLE.using one

( 1 ) QUICKLINK. After the CABLEhas been routed, position the CABLERETAININGCLIP in vertical position under the PULLEYand CABLEand tighten the PULLEYCONNECTIONcompletely.

See CABLEROUTINGDIAGRAMfor help in completing this step.

Tighten the PULLEYCONNECTIONSof the PULLEYBLOCK.

34.

3~.

36.

Insert one (1) I-3/4 IN. SQ. ENDCAPinto the end of the BENCHTOP,and fi',ree (3) 1-~.4 IN. SQ. CAPSinto the ends of the FRONTLEGas shown on drawing.

SECURELYassemble the BENCHTOPto the FRONTLEGas shown on drawing, us:.:g I:wo (2) 3,'8

2-3/4 IN. BOLTS,four (4) 3/8.IN. WASHERS,and two (2) 3 8 IN. LOCKNUTS.

Insert three (3) 1-3/4 IN. SQ. ENDCAPSinto the ends of the REARLEGas shownon ~:-awing.

Assemble the REARLEGto the BENCHTOPas shown on drawing, using one (1) 3/8 X 3 IN. BOLT

four (4) 3/8 IN. WASHERS,and one (I) 3/8 IN. LOCKNUT. (TIGHTENTHE CONNECTION ENOUGH TO REMOVE THE PLAY, YET ALLOWING THE REAR LEG TO ROTATE FREELY)

7

IIF21/95